www.immersionrc.com

Page 1 of 2 12 LastLast
Results 1 to 10 of 12

Thread: Vortex pro 250 throttle up

  1. #1
    Forum Member
    Join Date
    Feb 2016
    Location
    Mississippi
    Posts
    35

    Vortex pro 250 throttle up

    I have been flying the vortex for a couple of weeks now and no matter what preset tune I use , when i go above half throttle or especially a punch out it sounds like the motors are rapidly cutting out, it is not a smooth acceleration and it continues as long as you are throttled up. Props are good no visible problems and have re run the wizard. No firmware upgrades have been performed.
    Thanks

  2. #2
    Forum Member
    Join Date
    Dec 2011
    Location
    PNW USA
    Posts
    3,412
    What batt.?

  3. #3
    Forum Member
    Join Date
    Feb 2016
    Location
    Mississippi
    Posts
    35
    4s Tattu 1300 mah 75c

  4. #4
    Forum Member
    Join Date
    Apr 2016
    Posts
    1,943
    What does your voltage say while full throttle?

  5. #5
    Forum Member
    Join Date
    Feb 2016
    Location
    Mississippi
    Posts
    35
    on a fresh pack it'll usually go to 14 , but even when I'm hovering at around half throttle and I go to increase throttle slightly you'll hear and see the quad kind of shutter, not nearly as bad as Full Throttle but you still notice it.

  6. #6
    Forum Member
    Join Date
    Apr 2016
    Posts
    1,943
    Can you try puting on 4 brand new props. And also check of your motor shafts aren't bend.

  7. #7
    Forum Member
    Join Date
    Feb 2016
    Location
    Mississippi
    Posts
    35
    installed 4 new 5040 bull nose props with same results. ckd the shafts and found no negative results. Installed new props and used a ruler to ck the track of the blades.
    Thanks

  8. #8
    Forum Member
    Join Date
    Feb 2011
    Location
    Netherlands
    Posts
    9,693
    Can you pop the top plate off and make sure the FC is still screwed down properly? And bottom connectors are in fully and not skewed?
    Velvety smooth drone pilot for hire

  9. #9
    Forum Member
    Join Date
    Feb 2016
    Location
    Mississippi
    Posts
    35
    Flight controller secured and connections are good.

  10. #10
    Forum Member
    Join Date
    Feb 2016
    Location
    Mississippi
    Posts
    35
    Deleted
    Last edited by hodges42; 13th January 2018 at 09:54 PM.

Similar Threads

  1. Vortex 285 won't throttle down
    By dnez in forum Immersion Vortex Support
    Replies: 1
    Last Post: 21st May 2016, 12:10 PM
  2. vortex throttle beep
    By billj in forum Immersion Vortex Support
    Replies: 0
    Last Post: 30th October 2015, 08:21 AM
  3. Replies: 10
    Last Post: 21st September 2015, 03:48 AM
  4. DX6/9 Throttle Cut Switch on Vortex
    By kin3tix in forum ImmersionRC
    Replies: 4
    Last Post: 28th July 2015, 08:48 PM
  5. Vortex Throttle jerking
    By Kenny9999 in forum ImmersionRC
    Replies: 0
    Last Post: 27th July 2015, 03:16 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •