Page 26 of 26 FirstFirst ... 16242526
Results 251 to 257 of 257

Thread: Powercube FPVision

  1. #251
    Quad newbie
    Join Date
    Aug 2013
    Location
    Shoreline WA
    Posts
    626
    Neither probably effect the ability to show rssi from the Crossfire, if I remember correctly, there us a specific rssi-crossfire setting on the osd menu.

    Sent from my Pixel XL using Tapatalk
    W7STE

  2. #252
    Navigator
    Join Date
    Jan 2018
    Posts
    16
    Thanks Steve for all the help everything is working as it should and I am getting the same RSSI readings in my OSD that you posted.

  3. #253
    Quad newbie
    Join Date
    Aug 2013
    Location
    Shoreline WA
    Posts
    626
    Glad it all worked for you, adds that extra bit of confidence when pushing the envelope.

    Sent from my Pixel XL using Tapatalk
    W7STE

  4. #254
    Navigator
    Join Date
    May 2016
    Posts
    9
    Hey,
    i finished a RotorX tbs vision. I bought a part here, a part there, waited a long time from tbs HK. I am looking for channel map of the tbs stack to Taranis, the built in buzzer can be moved on OSD NOR/REV I just wonder if there is a better way to know how the TBS stack channel numbers match Taranis channels.
    i have done a opentx v2.2.1 update, Taranis tx and almost all my rx’s to latest firmwares. The vendetta and QQ190’s need done. I’m also doing a revamp of all my quads to be the same as in switch function/location, but not as far as the same rx id number ( might have problems at a Fpv meet )
    i can move buzzer in beataflight/cleanflight(butterflight ?) on the Taranis, and in the tbs stacks OSD’. I can hook it up, change, look, I was hoping not do it 8 times (TBS stack OSD goes from channel 5 to 13)

  5. #255
    Navigator WDZaphod's Avatar
    Join Date
    May 2013
    Location
    Switzerland
    Posts
    260
    Any informations about BST Support for Betaflight 3.4.0 ? Will my FPVision work with it?

  6. #256
    Navigator
    Join Date
    Dec 2018
    Posts
    1
    Hi! Please help me hook up my TBS fpvision layer to my new fc if possible.

    I switched to a Helio Saping AIO FC and would like to use the tbs OSD
    I use the BN-880 GPS, but have to clue how to wire it so the OSD gets the info or how to control the OSD with stick commands. I see there is a tx2 and rx2 pins on the fpvision board. Would that be what is used to control the board from another FC than the Colibri?

  7. #257
    Navigator WDZaphod's Avatar
    Join Date
    May 2013
    Location
    Switzerland
    Posts
    260
    Not sure if this is possible at all. For sure you need to wire up the BST bus to the I2C Bus of your FC. Serial UART connection is AFAIK not required. But I'm not sure if all Betaflight targets include the BST/I2C drivers, or only the colibri one?
    And take care, the FPVision Stack uses the Bolts for Battery Power. Many Flight controllers have all their mounting holes on ground, so mounting it as a stack without isolation will cause a direct battery short.
    ---> Let's make the Lab great again! <---

    Caipi 2 / Strix Goblin / RVJet / Mini Race Wing / Mini Talon
    Copters from Whoop to XClass

Similar Threads

  1. TBS POWERCUBE
    By Sandman1646 in forum Team-Black Sheep
    Replies: 1751
    Last Post: 14th February 2018, 06:03 AM
  2. LEDs for TBS PowerCube
    By SeanyP in forum Team-Black Sheep
    Replies: 3
    Last Post: 17th March 2017, 04:27 PM
  3. PowerCube and DFU Not Getting Along
    By WingsThree in forum TBS Support
    Replies: 0
    Last Post: 4th May 2016, 05:03 PM
  4. Need help with my TBS powercube!
    By Smallz in forum OSDs & Flight Controllers
    Replies: 0
    Last Post: 4th May 2016, 12:37 PM
  5. help with powercube and x4r
    By Gorillionaire in forum RC TECH
    Replies: 1
    Last Post: 25th March 2016, 11:53 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •