Just build and add li-po and radio gear for a complete multirotor


QAV ZMR 250 Carbon Fiber Quadcopter Frame with CC3D Flight Controller Brushless Motor ESC



http://www.gearbest.com/multi-rotor-...80.html?wid=21





Carbon Fiber Mini 250 FPV Quadcopter Frame Specifications:
Material: Carbon Fiber and Fiber Glass mix
Size: 220mm diagonally, 175mm wide, 130mm long motor-to-motor;
Maximum Propeller: 5 inch
Motor Mount: M2 12mm - 16mm
Flight Controller Mount: 30.5mm x 30.5mm
Board Camera Mount: 32mm x 32mm


MT1806 2280kv Brushless Motor Specification:
KV: 2280
Max Trust: 460g
No. of Cell: 2-3S
Framework: 12N14P
Propeller: 5 inch - 6 inch
Length: 26.7mm
Shaft: 2mm
Diameter: 23mm
Weight: 18g


12A Simon-k ESC Specifications:
Max Continuous Load: 11 amps
Burst Current: 16A / 10sec
BEC: 5v / 1 amp max
Li-po Cells: 2 to 3 cells
Cables are fitted with female 2mm bullet connectors
Weight: 10g
Dimensions: 24mm L x 18mm W x 7mm H ( 29mm in length including capacitor )
15cm signal wire / 5v power
5cm motor wires ( including 2mm bullet connector )


CC3D Flight Controller
Powerful STM32 32-bit micro controller running at 90MIPs with 128KB Flash and 20KB RAM
Software support for Windows, Mac and Linux
Direct high speed USB support with no drivers required, a truly plug and play device
Spektrum satellite receiver support
Futaba S-BUS hardware support
Innovative Flexi-port technology for superior port flexibility
4Mbits on-board EEPROM for configuration storage
Sensors and components
Supports several common RC inputs: 6 PWM channels, combined PPM, Spektrum / JR DSM2, DSMJ, DSMX satellites, and Futaba S.Bus receivers
Simultaneous support for multiple receivers
Receiver port functions ( configurable ): 6 PWM input channels or combined PPM stream, 4 PWM output channels
Main-port functions ( configurable ): Serial telemetry ( default ) , GPS, S.Bus, Spektrum / JR satellites
Flexi-port ( configurable ): Serial telemetry, GPS, Spektrum / JR satellites, or I2C peripherals ( under development )
Camera stabilization: Supports up to 3-axis camera mounts with stabilization and manual control from any of configured receivers
USB and serial telemetry and configuration ( including wireless with optional radio modules )


Package Contents:
1 x 250 Quadcopter Frame,
1 x ESC Connection Board,
4 x MT1806 2280KV Brushless Motor,
4 x 12A Simonk ESC,
4 x 5030 Propeller,
1 x CC3D Flight Controller,
4 x Propeller Ring,
2 x Connecting Cable Set,
1 x Accessory Set

RoboCat 270mm Quadcopter DIY Frame Kit 12A ESC / CC3D FC / Marspower 2204 Motor / Propeller


http://www.gearbest.com/multi-rotor-...18.html?wid=21







Unboxing Video


https://youtu.be/dkOfNxpZB_0]https:/...be/dkOfNxpZB_0
First Flight Video


https://youtu.be/NZKte_CjrHk]https:/...be/NZKte_CjrHk


Specification:
- Wheelbase: 270mm
- Material: Carbon fiber
- Removable hood make from shock-absorbing PC materials
- Model net weight: 190g
- 1.5mm thick fuselage and 3mm thick arms
- No assembled, just kit

Marspower 2204 2300KV motor:
KV Value(RPM / V): 2300
Motor Diameter(mm): 34
Motor Length(mm): 27
Net Weight(g): 33
Weight(g): 43
Color: Black
Shaft Diameter(mm): 3


SimonK 12A ESC:
- Constant Current: 12A
- Input Voltage: 1 - 3 cell Lipoly
- BEC Output: 5V / 1A
- PWM: 8 KHz
- Max RPM: 240,000rpm for 2 Pole Brushless Motor
- Size: 22 x 17 x 7
- Weight: 8g


CC3D Flight Controller
Powerful STM32 32-bit micro controller running at 90MIPs with 128KB Flash and 20KB RAM
Software support for Windows, Mac and Linux
Direct high speed USB support with no drivers required, a truly plug and play device
Spektrum satellite receiver support
Futaba S-BUS hardware support
Innovative Flexi-port technology for superior port flexibility
4Mbits on-board EEPROM for configuration storage
Sensors and components
Supports several common RC inputs: 6 PWM channels, combined PPM, Spektrum / JR DSM2, DSMJ, DSMX satellites, and Futaba S.Bus receivers
Simultaneous support for multiple receivers
Receiver port functions ( configurable ): 6 PWM input channels or combined PPM stream, 4 PWM output channels
Main-port functions ( configurable ): Serial telemetry ( default ) , GPS, S.Bus, Spektrum / JR satellites
Flexi-port ( configurable ): Serial telemetry, GPS, Spektrum / JR satellites, or I2C peripherals ( under development )
Camera stabilization: Supports up to 3-axis camera mounts with stabilization and manual control from any of configured receivers
USB and serial telemetry and configuration ( including wireless with optional radio modules )




Package Contents:
1 x Quadcopter Frame,
4 x Motor,
4 x ESC,
4 x Propeller,
4 x Propeller Ring,
1 x CC3D Flight Controller Set




QAV210 210mm Quadcopter Frame Kit 12A ESC / Afro Naze32 6DOF FC / Marspower 2204 Motor / Propeller


http://www.gearbest.com/multi-rotor-...11.html?wid=21





Specification:
Wheelbase: 210mm
Material: Carbon fiber
Model net weight: 65g
1.5mm thick fuselage and 3mm thick arms
No assembled, just kit


Marspower 2204 2300KV motor:
KV Value(RPM / V): 2300
Motor Diameter(mm): 34
Motor Length(mm): 27
Net Weight(g): 33
Weight(g): 43
Color: Black
Shaft Diameter(mm): 3

EMAX BLHeli 12A ESC:
Constant Current: 12A
Input Voltage: 1 - 3 cell Lipo
BEC Output: 5V / 1A


Afro NAZE32 6DOF flight controller :
The Naze32 flight controller is extremely simple to setup
Battery voltage monitoring
Built-in FrSky telemetry converter
Flexible motor outputs, support various airframe types
Modern 32-bit processor running at 3.3V / 72MHz
Extra bright LEDs
Modern GUI for all operating systems


Package Contents:
1 x Quadcopter Frame,
4 x Motor, 4 x ESC,
4 x Propeller,
4 x 5045 Propeller Ring,
1 x NAZE32 6DOF Flight Controller Set,
1 x ESC Connecting Board,




Flycolor GB210 210mm Carbon Fiber DIY Frame Kit



http://www.gearbest.com/multi-rotor-...17.html?wid=21





Main Features:
- The integrated design with arms and 3mm full carbon fiber plates is ideal for RC Racing, intense 4S flight. It also fits various camera mounts.
- The F3 10DOF DELUXE flight controller incorporates a barometer and a compass. It is extremely compact, with a size of 36 x 36mm and a weight of only 5g.
- The RAPTOR Series ESC is specially designed for racing drones, therefore, it is pretty small and light, only 9.7g. Its BLHeli firmware can provide you with unprecedented experience of immediate throttle response, fast braking and long-time flight! It supports Oneshot125 and Damped Light.


Specifications:
Carbon Fiber Frame
Wheelbase: 210mm
Lower plate: 3mm
Upper plate: 1.8mm
Lateral plate: 1.5mm
Weight: about 100g


F3 10DOF DELUXE Flight Controller
Description:
SP Racing F3 is designed to give awesome flight performance based on tried and tested sensors while also providing unparalleled I/O capabilities.
Compared to ACRO version, the DELUXE one is quite impressing with 10DOF, always-on I2C port for OLED display and bigger cache memory of the CPU.


Main Features:
- Next-generation CPU contributes to faster calculations and shorter loop time
The STM32F3 CPU supports next-generation processor, efficient hardware floating-point operations, and faster ARM Cortex - M4 core computing.


- Outstanding multitasking with no-compromise I/O
Use all the features simultaneously! It is possible to connect your OSD, SmartPort, SBu, GPS, LED strip, battery monitoring, sonar, and 8 motors at the same time!


- Easily achievable improvements of setup with the help of flight logs
The on-board high-capacity black box records the flight logs, which can be used to optimize your tuning and to see the results of your setup without guesswork.


- OneShot ESC and programmable LEDs
Fully supporting OneShot, it also features easy PID tuning and a sharper response. The multi-colored LED strips are great for FPV racing, line-of-sight flying and night flying.


- Ideal for steady flight
The SP Racing F3 builds on tried and tested software, processor and sensor technology to make your aircraft fly as if it is on rails.


- Configurable
The SP Racing F3 runs Cleanflight which can be configured to suit your needs via a cross-platform GUI (Windows / OSX / Linux).


- Developer friendly
Developer friendly debug port (SWD), boot mode selection, and unbrickable bootloader are available, thus, opening the way for upgrades.


- Broad RC receiver support
It supports SBus, SumH, SumD, Spektrum1024 / 2048, XBus, PPM, PWM receivers, and requires no external inverter.


- Suitable for 250, 280, 180, 210mm FPV racing quadcopter


Configuration: 12N14P
Maximum continuous current (A): 180S 12A
Maximum continuous power (W): 180S 145W
Maximum efficiency power: 5A


Flycolor RAPTOR 330 BLHeli 2 - 4S 20A OPTO ESC
Input voltage: 2 - 4S Li-Po
Instantaneous current: 30A
Continuous current: 20A

Package Contents:
1 x GB210 Carbon Fiber Frame,
4 x Motor,
4 x ESC,
4 x Propeller,
1 x F3 10DOF Flight Controller,
1 x PDB



Flycolor DUBAI GB210 210mm Carbon Fiber DIY Frame Kit


http://www.gearbest.com/rc-quadcopte...47.html?wid=21







Build video
https://youtu.be/5Q6UUYjnZ-0


Maiden flight
https://www.youtube.com/embed/C1r42lXh0BA


Frame:
Lens seat pitch ( support CCD, CMOS camera board aircraft )
Upper body version with a plurality of antenna holes to facilitate fixed antenna
Body with 1.5MM 3K full carbon fiber
Rational layout, easy to install
ESC can be installed in arm, it can also be installed in the fuselage
Compatible AOMWAY 700 line camera mounts
Diagonal Wheelbase: 210mm
Rack Weight: 80g
Support Motor: 1306 KV3000 / 1804 KV2300 / 1806 KV2300 ( 1806 / 4045 recommend inch paddle )
Motor Diameter: 27.9mm
Motor Height: 31.7mm
Support Propeller: 4 / 5 inch
Mounting Dimension: 200 x 165 x 62mm
Net Weight: 91g






Motor : Emax RS2205 2300KV
The new RS2205 2300KV Racing Edition motors from Emax are some of the best racing motors we've seen. They have very light weight designs and are using Japanese bearings for better performance.


Main Features:
High strength N52 neodymium magnets
Active cooling fans greatly reducing motor temperature
Low CG, light weight design
Japanese bearing for performances
Dual lock CW / CCW lock-nuts


Specifications:
Number of cells: 3 - 4S
Shaft: M5
KV: 2300
Max. thrust: 1024g
Diameter: 27.9mm
Propeller suggested: HQ 5045 BN


4Pcs / Set OCDAY Spare 20A Mini 2 - 4S Lipo ESC ONESHOT125
Super compact, lightweight, high performance speed controller for your racing multi-rotor.
Pre-flashed with BLHeli and ready to use with oneshot ( aka oneshot125 / PWMsync ) mode via compatible flight controllers running cleanflight or similar.
These ESC set do not have BEC, you will need to supply 5V power to your flight controller with a UBEC or stepdown voltage regulator.


Power Distribution Board 4-layer PCB Two-way BEC 5V 12V PDB
Input voltage range ( 2S - 6S operation ): 7.2 - 26V DC
Regulated 5V and 12V outputs
LED power indicators ( 5V, 12V outputs )


ESC outputs:
Continuous current: 20A
Peak current: 30A
BEC 5V output: Designed for RC Receivers, Flight controllers, OSD, and Servos
Continuous current: 3 Amps


SP Racing F3 Flight Control Deluxe 10 DOF Fitting for Multirotor
Main Features:
Supports more flight controllers, including CC3D, CJMCU and Sparky
Supports OneShot ESC and more than 8 RC channels
Additional PID controllers that uses floating point arithmetic operations ( now has 3 built-in PID controllers )
Many more features such as RGB LED strip support, Autotune, In-flight PID tuning with your radio, blackbox flight data logging etc.


Detail Information
Flight Performance
The SPR F3 builds on tried and tested software, processor and sensor technology to make your aircraft fly like it's on rails


No-Compromise I / O
Use all the features all the time; e.g. Connect your OSD + SmartPort + SBus + GPS + LED Strip + Battery Monitoring + Sonar + 8 motors - all at the same time


Configurable
The SP F3 runs Cleanflight which can be configured to suit your needs using a cross-platform GUI ( Windows / OSX / Linux )


Tiny
The RacingF3 has a standard 35 x 35mm form-factor with 30mm mounting holes and weighs just 6 grams


Flight Logging
On-board high-capacity black box flight log recorder - optimize your tuning and see the results of your setup without guesswork


Next-generation CPU
The RacingF3 has an ARM Cortex-M4 72Mhz CPU with Math co-processor ( FPU ) for efficient flight calculations that gets more done in less time
Loop times up to ~2x as fast as previous-generation STM32F1 based boards


Developer Friendly
Developer friendly debugging port ( SWD ) and boot mode selection


OneShot ESC
Full support for OneShot ESCs for easy PID tuning and a sharper response


Programmable LED
Dedicated output for programmable LEDs - great for orientation, racing and night flying


Battery Monitoring
Battery monitoring ports for voltage and current


Sonar
Sonar support for precision low-altitude hold


I2C Port
I2C port always powered, perfect for external sensors or always-on OLED screen


Buzzer
Buzzer port for audible warnings and notification