Results 1 to 6 of 6

Thread: Mudskipper Advanced Board requires additional parts

  1. #1
    Navigator
    Join Date
    Mar 2013
    Posts
    4

    Mudskipper Advanced Board requires additional parts

    I ordered the Mudskipper kit and also the advanced board that includes the Dodo board. There is no indication that I need to order additional parts to run the advanced board but it seems you also need to order the 2mm spacers and supply your own M3x16mm screws to replace the M3x22 used with the stock board. Since there is no instructions with the advanced board, how was I suppose to know that other parts are required?

  2. #2
    ImmersionRC Support Guru swillhide's Avatar
    Join Date
    Aug 2012
    Location
    Mountain House, Ca
    Posts
    8,443
    You are right, this was our fault 100%. Our fault so much that I even told you that I would send you the parts for free and fix the listing on our web site. I will even go as far as throwing in new screws, and you are 100% right there was no way for you to know but like your ticket said and your testimonial said and now that you repeated it also here I will hold to my offer and send that stuff to you.

    Steven
    Last edited by swillhide; 23rd February 2016 at 07:32 PM.
    AMA # 1015480 HAM Callsign # Procrastinating..
    Futaba 9c w/Ezuhf /Skywalker 1880 or anything else that I can Lawn Dart.
    Retired: Disco(Sold), Skywalker 1900(Dirt Nap), Qav540g/Nazav2/Iosd mk2

  3. #3
    Navigator
    Join Date
    Mar 2013
    Posts
    4
    That would be swell! I don't think I got the part about sending the screws. Last message I got said if I ordered the screw, you'd put the spacers in with it but I couldn't even find M3x16 buttonhead screws on RMRC.

  4. #4
    ImmersionRC Support Guru swillhide's Avatar
    Join Date
    Aug 2012
    Location
    Mountain House, Ca
    Posts
    8,443
    I have the spacers , and m3x18 and m3x14 set to be shipped to you tomorrow. Might be a little long or so but 2mm is small and no one will notice.

    Steven
    AMA # 1015480 HAM Callsign # Procrastinating..
    Futaba 9c w/Ezuhf /Skywalker 1880 or anything else that I can Lawn Dart.
    Retired: Disco(Sold), Skywalker 1900(Dirt Nap), Qav540g/Nazav2/Iosd mk2

  5. #5
    Navigator
    Join Date
    Mar 2013
    Posts
    4
    Thanks a bunch, Steven. I shoved a 2mm G10 part in there and measured. I think the 14mm ones would work as it looks like they should get far enough to catch the nylon in the nuts.

  6. #6
    Navigator
    Join Date
    Apr 2014
    Posts
    91
    I just found this out the hard way as the listing hasn't been updated, why aren't the spacers part of the advanced PDB though, along with the necessary screws?

    Anyways, I have trust you guys will resolve this...

Similar Threads

  1. Fpv mudskipper not working with battery
    By littlet23060 in forum RMRC Support
    Replies: 19
    Last Post: 3rd January 2016, 10:18 PM
  2. Replies: 4
    Last Post: 6th December 2015, 06:31 PM
  3. XuGong V2 - take off and landing requires full throttle
    By rickycinco in forum ImmersionRC
    Replies: 10
    Last Post: 14th April 2015, 02:34 AM
  4. Replies: 3
    Last Post: 13th May 2014, 02:19 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •