Page 1 of 32 12311 ... LastLast
Results 1 to 10 of 316

Thread: The Lumenier LUX Flight Controller - STM32F303 32-bit processor

  1. #1
    Forum Member
    Join Date
    May 2013

    The Lumenier LUX Flight Controller - STM32F303 32-bit processor

    Introducing the new Lumenier LUX flight controller -

    The Lumenier LUX flight controller provides high quality flight control using the powerful F3 processor along with top of the line hardware. Unleash the capabilities of your FPV Racing Quadcopter with the Lumenier LUX Flight Controller. Achieve gyro refresh rates up to 8kHz using popular Betaflight and Raceflight firmware along with ultra low looptimes. The LUX is Cleanflight compatible using the RACE target.

    The Lumenier LUX is a very low profile board allowing it to be mounted in a variety of ways. The board also comes with a set of pin headers you can optionaly solder on. Alternatively, signal wires can be soldered directly to the pads to save on size and weight. The LUX supports PPM or Serial RX (including Futaba, FrSky, S.BUS). A signal inverter is already included for S.BUS. Please note: Baseflight firmware is not supported, and PWM input for individual channels is not supported.


    • USB Conflict resolution - Hardware inversion, SBUS or telemetry can be used on any of the 3 available hardware serial ports. USB will not interfere with peripherals.
    • BLHeli flashing supported (BLHeli bootloader pass-through).
    • Betaflight ready - including 8khz Gyro sync.
    • Dedicated Boot button for easy firmware flashing.
    • Reinforced solder pads for trouble-free direct soldering.
    • Extremely low profile design.
    • Recessed, sideways pin headers. Also enables soldering of all wires directly to pads without use of any pin headers.
    • Integrated FRSky RSSI Filter (RC filter).
    • Input voltage 6v to 24v. Power the board directly from flight pack up to 6S (on 'BAT' pad only!).
    • VIN + VBAT merged - A single wire to power the board will provide voltage input and Telemetry/OSD voltage data.
    • Filtered voltage output - output 5v 1000mAh (and 3.3v where applicable) to power peripherals such as GPS, RX, BLACKBOX, OSD. 5v/3.3v RX selectable.


    • STM32F303 32-bit processor
    • MPU6500 Gyro/Accelerometer
    • High quality, gold plated PCB
    • Highest quality components, individually sourced to meet Lumenier standards
    • Micro USB connector for programming
    • Dimensions: 36x36x6mm (includes USB in height)
    • Mounting Holes: 30.5mm square to center of holes
    • Weight: 6g


    • 1x Lumenier Lux Flight Controller
    • 2x 2x7 Straight Pin Headers


    Download the Lumenier Lux User Manual
    Download Cleanflight (Load the "LUX" target)

    Order Here -

    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	lumenier-lux-flight-controller-lead_1.jpg 
Views:	6501 
Size:	111.3 KB 
ID:	69028   Click image for larger version. 

Name:	lumenier-lux-fc.jpg 
Views:	8757 
Size:	47.2 KB 
ID:	68443   Click image for larger version. 

Name:	lumenier-lux-top.jpg 
Views:	610 
Size:	225.2 KB 
ID:	68446   Click image for larger version. 

Name:	lumenier-lux-angle.jpg 
Views:	515 
Size:	208.8 KB 
ID:	68444   Click image for larger version. 

Name:	lumenier-lux-back.jpg 
Views:	689 
Size:	195.7 KB 
ID:	68445  
    Last edited by Andy_GetFPV; 27th April 2016 at 03:38 PM.

  2. #2
    Forum Member
    Join Date
    Jan 2015
    Chicago, USA
    Looks awesome!

  3. #3
    Forum Member
    Join Date
    Jun 2012
    New Zealand
    Quote Originally Posted by sammydigits View Post
    Looks awesome!
    I fully agree!

  4. #4
    Forum Member
    Join Date
    Nov 2011

    OUTPUT: 5V 1000mA for those interested
    Last edited by chatch; 3rd December 2015 at 08:10 AM.
    [QUOTE=jimmaplesong;128705]When you're outraged at chatch, please don't quote his bullshit.[/QUOTE]

  5. #5
    Forum Member
    Join Date
    Jan 2013
    So when do we get to see team pilots flying this controller? We need on-board video!

  6. #6
    Forum Member
    Join Date
    Nov 2015
    Is there no on board flash memory for blackbox?

  7. #7
    Forum Member
    Join Date
    Nov 2015
    How many amps can you pull through the 5v? Since it's filtered power output, can we power a camera and video transmitter? This looks awesome, I'll get one for my next build!

  8. #8
    Forum Member
    Join Date
    Nov 2015
    Ah I found it on the user manual. Can you do people a favor and add the "1000ma 5v" rating to this post for others?

  9. #9
    Forum Member
    Join Date
    Jan 2015
    Great looking Flight Controller, but I'm confused, shouldn't there be a minimum of 4 motor outputs?? Did I miss something?

  10. #10
    Forum Member
    Join Date
    Oct 2013
    Canberra - Australia
    Quote Originally Posted by vansmak View Post
    Great looking Flight Controller, but I'm confused, shouldn't there be a minimum of 4 motor outputs?? Did I miss something?
    There is ! Labled 1, 2 3 4 on the top, with ground points next to each. love the sensible layout, should make for come tangle free builds! Ordered 2, Cant wait

Similar Threads

  1. Replies: 5
    Last Post: 26th September 2016, 03:02 PM
  2. Replies: 20
    Last Post: 27th January 2016, 05:02 AM
  3. Lumenier QAV540G/QAV500G FLIGHT VIDEOS
    By Pottsburg in forum LUMENIER
    Replies: 96
    Last Post: 10th March 2015, 07:00 PM
  4. Replies: 8
    Last Post: 17th February 2015, 07:54 AM
  5. CC3D Flight Controller ( Lumenier edition ) Died.
    By FlyingDutchman in forum OSDs & Flight Controllers
    Replies: 1
    Last Post: 11th November 2014, 08:29 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts