Page 1 of 11 123 ... LastLast
Results 1 to 10 of 105

Thread: Lumenier Mini 20A ESC w/ SimonK AutoShot, 5V/1A BEC (2-4s)

  1. #1
    Navigator Andy_GetFPV's Avatar
    Join Date
    May 2013
    Location
    Florida
    Posts
    568

    Lumenier Mini 20A ESC w/ SimonK AutoShot, 5V/1A BEC (2-4s)

    The Lumenier Mini 20 amp ESC with customized SimonK firmware including OneShot auto-detect is the perfect ESC to use on mini FPV quads such as the QAV250. This ESC is small in size (27x14.5x6mm) and big on power, supporting 20A on 4s. The ESC comes pre-loaded with the newest firmware, which is compatible with new features like "OneShot" (no soldering required, it will auto-detect if OneShot is enabled), Comp PWM (similar to KISS braking feature), compatible with all Lumenier motors up to 4 cell.

    The Lumenier 20 amp AutoShot ESCs have been tested and are compatible with all Lumenier motors (FX1806, FX2206, FXC2206, FX2208), 2S-4S, both 5" and 6" props without sync loss issues or cogging.

    The Simonk AutoShot firmware is pre-calibrated with endpoints 1060us - 1860us. This corresponds to the default endpoints in both Baseflight and Cleanflight. Therefore, "Calibration" procedure is not necessary.

    Click image for larger version. 

Name:	lumenier-20amp-autoshot-2-4s-penny.jpg 
Views:	601 
Size:	72.2 KB 
ID:	62599 Click image for larger version. 

Name:	lumenier-20amp-autoshot-2-4s-back.jpg 
Views:	1181 
Size:	49.8 KB 
ID:	62600 Click image for larger version. 

Name:	lumenier-20amp-autoshot-2-4s-close.jpg 
Views:	545 
Size:	61.0 KB 
ID:	62601

    Features


    • Active Braking / Damped Light / Comp_PWM
    • AutoShot (OneShot125 / FastPWM Auto Detect)
    • Customized to drive all motors without sync issues or cogging.
    • Pre-soldered cables and connectors make installation easy


    To enable new features on Baseflight:
    - On Configuration tab, check "Enable OneShot" and "Enable FastPWM"
    - Scroll down and click "Save"

    To enable new features on Cleanflight:
    -On Configuration tab, check the "Enabled" box next to "ONESHOT125" Feature
    -Scroll down and click "Save"

    Specifications


    • Max continuous load: ~20 amps
    • Burst Current: 30A/10sec
    • BEC: 5v/1amp max
    • Lipo Cells: 2 to 4 cells
    • Cables are fitted with female 2mm bullet connectors
    • Weight: 4g (board) 8g (total with wires and connectors)
    • High quality N-FET only flashed with SimonK firmware and 5v 1A BEC

    Dimensions


    • 27mm L x 14.5mm W x 6mm H
    • 100mm signal wire / 5v power
    • 50mm motor wires (including 2mm bullet connector)
    • 70mm ESC power wires


    Order here:
    http://www.getfpv.com/lumenier-mini-...-bec-2-4s.html

    Last edited by Andy_GetFPV; 26th May 2015 at 05:42 PM.

  2. #2
    Grass Surfer bagofsoup's Avatar
    Join Date
    Jan 2015
    Location
    Citrus, FL
    Posts
    497
    subbed! Those look really tiny. Great stuff GetFpv
    In hoc signo vinces

  3. #3
    Navigator Hally1983's Avatar
    Join Date
    Sep 2013
    Location
    Scotland
    Posts
    708
    Ordered a set last night so we shall see if there any good in comparison to Blheli
    Follow My Builds: plus.google.com/u/0/+HallyFPV/posts
    Team-Legit FOHDY 40" - Cobra 2217/1180kv, 40a HK Esc, TBS Core Pro & GPS, TBS Crossfire
    Mini Talon - Sunnysky 2216 /1250kv, 40a Xrotor Esc, TBS Core Pro, TBS Crossfire
    Lumenier QAV-R 5" - Kiss FC, Kiss 24aRE Esc (Dshot600), Lumenier 2206-2350kv Motors, Lumenier 600mw VTX, TBS Crossfire
    Lumenier QAV210 - TBS Colibri FC, TBS FPVision (OSD/VTX), ZTW 30a Blheli-S (Multishot), Emax RS2205-S 2300kv, TBS Crossfire

  4. #4
    Lumenier.com timnilson's Avatar
    Join Date
    Mar 2011
    Location
    Florida
    Posts
    3,088
    Please let us know what you find out!!

  5. #5
    Navigator Hally1983's Avatar
    Join Date
    Sep 2013
    Location
    Scotland
    Posts
    708
    Quote Originally Posted by timnilson View Post
    Please let us know what you find out!!
    Will do Tim, ive ordered the Carbon QAV250 with your new Gopro cover plate too, so ill fire some cobra 1960kvs on with those ESCs. I do see the new version of BLHeli 14 which is about to be released looks v nice so im hoping the simonk autoshot is not dissimilar. Ill compare them both anyway and report back.

    I take it there is no USB flasher / software available to adjust the parameters on these?

    Cheers,
    Last edited by Hally1983; 30th May 2015 at 09:34 PM.
    Follow My Builds: plus.google.com/u/0/+HallyFPV/posts
    Team-Legit FOHDY 40" - Cobra 2217/1180kv, 40a HK Esc, TBS Core Pro & GPS, TBS Crossfire
    Mini Talon - Sunnysky 2216 /1250kv, 40a Xrotor Esc, TBS Core Pro, TBS Crossfire
    Lumenier QAV-R 5" - Kiss FC, Kiss 24aRE Esc (Dshot600), Lumenier 2206-2350kv Motors, Lumenier 600mw VTX, TBS Crossfire
    Lumenier QAV210 - TBS Colibri FC, TBS FPVision (OSD/VTX), ZTW 30a Blheli-S (Multishot), Emax RS2205-S 2300kv, TBS Crossfire

  6. #6
    Navigator ViperSD's Avatar
    Join Date
    Apr 2015
    Location
    Raleigh, NC ... USA
    Posts
    86
    What is the refresh rate / optimum looptime setting for these?

    Are the BEC's linear or switched?
    Last edited by ViperSD; 31st May 2015 at 02:02 AM.

  7. #7
    Navigator Hally1983's Avatar
    Join Date
    Sep 2013
    Location
    Scotland
    Posts
    708
    Quote Originally Posted by timnilson View Post
    Please let us know what you find out!!
    Hi Tim,

    Can you clarify for me, can 3x of these esc be ran with signal wire only and 4th with all 3 wires for power/gnd?

    Or must all 4 escs have all 3 wires connected?

    Asking as im trying a low profile build to get naze underneath my QAV.

    Thanks,
    Follow My Builds: plus.google.com/u/0/+HallyFPV/posts
    Team-Legit FOHDY 40" - Cobra 2217/1180kv, 40a HK Esc, TBS Core Pro & GPS, TBS Crossfire
    Mini Talon - Sunnysky 2216 /1250kv, 40a Xrotor Esc, TBS Core Pro, TBS Crossfire
    Lumenier QAV-R 5" - Kiss FC, Kiss 24aRE Esc (Dshot600), Lumenier 2206-2350kv Motors, Lumenier 600mw VTX, TBS Crossfire
    Lumenier QAV210 - TBS Colibri FC, TBS FPVision (OSD/VTX), ZTW 30a Blheli-S (Multishot), Emax RS2205-S 2300kv, TBS Crossfire

  8. #8
    Navigator Andy_GetFPV's Avatar
    Join Date
    May 2013
    Location
    Florida
    Posts
    568
    Quote Originally Posted by Hally1983 View Post
    Hi Tim,

    Can you clarify for me, can 3x of these esc be ran with signal wire only and 4th with all 3 wires for power/gnd?

    Or must all 4 escs have all 3 wires connected?

    Asking as im trying a low profile build to get naze underneath my QAV.

    Thanks,
    Sure, that can work.

  9. #9
    Navigator Hally1983's Avatar
    Join Date
    Sep 2013
    Location
    Scotland
    Posts
    708
    Quote Originally Posted by Andy_GetFPV View Post
    Sure, that can work.
    Have you tested them like that Andy?

    Cheers
    Follow My Builds: plus.google.com/u/0/+HallyFPV/posts
    Team-Legit FOHDY 40" - Cobra 2217/1180kv, 40a HK Esc, TBS Core Pro & GPS, TBS Crossfire
    Mini Talon - Sunnysky 2216 /1250kv, 40a Xrotor Esc, TBS Core Pro, TBS Crossfire
    Lumenier QAV-R 5" - Kiss FC, Kiss 24aRE Esc (Dshot600), Lumenier 2206-2350kv Motors, Lumenier 600mw VTX, TBS Crossfire
    Lumenier QAV210 - TBS Colibri FC, TBS FPVision (OSD/VTX), ZTW 30a Blheli-S (Multishot), Emax RS2205-S 2300kv, TBS Crossfire

  10. #10
    Navigator Andy_GetFPV's Avatar
    Join Date
    May 2013
    Location
    Florida
    Posts
    568
    Quote Originally Posted by Hally1983 View Post
    Have you tested them like that Andy?

    Cheers
    Yeah it's nothing unique with this ESC, any could do that. The Flight controller only needs the signal wire/ground from each. Since these have included 5v BECs, then you can use 1 of them to provide 5v of power to your flight controller.

Similar Threads

  1. bad lumenier 12 amp simonk n-fet esc?
    By WillardSkillard in forum LUMENIER
    Replies: 19
    Last Post: 8th June 2015, 10:48 AM
  2. Lumenier 12 amp ESC w/ SimonK AutoShot
    By zgilbrech in forum FAQs
    Replies: 0
    Last Post: 25th May 2015, 02:13 PM
  3. Replies: 3
    Last Post: 6th May 2015, 10:56 AM
  4. Lumenier 30 amp ESC with SimonK Firmware
    By balbusky21 in forum RC TECH
    Replies: 0
    Last Post: 15th January 2014, 06:57 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •