Page 10 of 11 FirstFirst ... 891011 LastLast
Results 91 to 100 of 109

Thread: Skylark Tiny OSD III - Nightrams comprehensive page

  1. #91
    Navigator
    Join Date
    Apr 2016
    Posts
    1
    Has any one got the skylark config to work on windows 10. I have my tiny all wire and everything works , but I would like change some of the settings. I'm having a hard time getting it work on windows 10. I have installed the driver , I pull up the config and I see the com port, but nothing happens. Does any one have any suggestions

  2. #92
    Forum Member
    Join Date
    Apr 2012
    Posts
    657
    Voltage calibration you can do stationary
    Amp calibration you need xxamp draw and press read you can do this with motor or lamp pressing set can stationary

    Verstuurd vanaf mijn SM-G920F met Tapatalk
    Last edited by wippo76; 25th April 2016 at 01:55 AM.

  3. #93
    Navigator giteart's Avatar
    Join Date
    Mar 2014
    Location
    Greece
    Posts
    362
    Stejamb can't you find a computer with windows 7?

    Maybe you can try something I did in win7 and worked for me.
    Connect the usb to pc and skylark and then before opening the program, right click on it-> properties-> compatibility and select were it says compatibility mode -> run for windows XP. That fixed my problem.


    Also I have to say that my unit from factory was off by 0.2V and about 2~3A at wot. Calibration by using a wattmeter was easy and successful. I had to do it twice though to get it spot on.

  4. #94
    Forum Member
    Join Date
    Apr 2012
    Posts
    657
    I had also some troubles with the skylark usb stick
    I ended up with using a usb stick from feiyu tech (came with a fy dos ) and this works great
    Check in devices if your stick is starting good
    Always it has to do something with the drivers.

    Verstuurd vanaf mijn SM-G920F met Tapatalk

  5. #95
    Forum Member
    Join Date
    Apr 2011
    Posts
    1,143
    Do I enter the V and A reading in the program while the motor is running?
    No, It's not required
    The steps.
    1. motor running, then remember the current value and click the [read] button
    2. you can input the just current value when you stop motor.

    Also what is the purpose of the reset button? When do I press it and why?
    When you press the reset button, the OSD will be reinitialized, then read the new GPS position as takeoff point

    Skylark FPV Service Center
    [URL]http://www.skylarkfpv.com[/URL]

  6. #96
    Forum Member
    Join Date
    Apr 2011
    Posts
    1,143
    A special firmware for the Tiny OSD that can work without GPS and Current Sensor
    Tiny OSD Firmware_3.x.0

    Skylark FPV Service Center
    [URL]http://www.skylarkfpv.com[/URL]

  7. #97
    Forum Member
    Join Date
    Apr 2011
    Posts
    1,143
    A special firmware for the Tiny OSD that can work without GPS
    Tiny OSD Firmware_3.x.1

    Skylark FPV Service Center
    [URL]http://www.skylarkfpv.com[/URL]

  8. #98
    Forum Member
    Join Date
    Feb 2014
    Posts
    29
    Anybody else got problems with bricked tiny OSD after firmware upgrade?? I got the firmware 3.0 from skylark, but after upgrading I am not able to connect to the OSD.
    I tried to unlock the OSD by shorting pin 1 and 2 or pin 2 and 3 when connecting it to the configurator without success.
    So now I got a bricked OSD which was fully functional with firmware 2.9 before attemting the upgrade.
    The configurator tool is not possible to run on my windows 10 computer either, I had to use my old windows vista computer.
    I am not impressed with skylark support. They should atleast give me a discount for a new main board.

  9. #99
    Forum Member
    Join Date
    Apr 2012
    Posts
    657
    Did you flash trace 4 fw?

    Verstuurd vanaf mijn SM-G920F met Tapatalk

  10. #100
    Forum Member
    Join Date
    Feb 2014
    Posts
    29
    Quote Originally Posted by wippo76 View Post
    Did you flash trace 4 fw?

    Verstuurd vanaf mijn SM-G920F met Tapatalk
    I hope not! I flashed the firmware skylarkfpv gave me by email. I did say it was for tiny OSD, even sent a photo of the main board. fw 3.0 which should have gps pos in simple view. Now its bricked and useless.

Similar Threads

  1. Skylark Tiny Osd III with 6s
    By Norse in forum SkylarkFPV
    Replies: 22
    Last Post: 4th January 2015, 04:24 AM
  2. Comprehensive Tiny OSD III wiring diagram
    By OBwan in forum SkylarkFPV
    Replies: 8
    Last Post: 15th December 2013, 10:00 PM
  3. Help with Skylark Tiny OSD
    By gobigdale in forum SkylarkFPV
    Replies: 4
    Last Post: 19th October 2013, 01:00 AM
  4. Help with Skylark tiny osd
    By bigmoebbq in forum IFR - Video Link Discussion
    Replies: 7
    Last Post: 18th November 2011, 09:55 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •