www.immersionrc.com

Page 1 of 2 12 LastLast
Results 1 to 10 of 13

Thread: 600mW TX and Dominator RX No picture

  1. #1
    Navigator
    Join Date
    Jun 2012
    Posts
    132

    600mW TX and Dominator RX No picture

    I was testing a new camera. I plugged the power into the TX the wrong way for a second.
    Does it have polarity protection?
    Now I have no picture. Tried all the channels.
    Tried another RX/TX set and the goggles are ok.
    Is there a way to know if its the TX or possibly the RX.
    Does anyone know of a repair centre near Spain if i need to send it off?
    Cheers

  2. #2
    ImmersionRC Support Guru swillhide's Avatar
    Join Date
    Aug 2012
    Location
    Mountain House, Ca
    Posts
    8,443
    Does the red light come on?
    AMA # 1015480 HAM Callsign # Procrastinating..
    Futaba 9c w/Ezuhf /Skywalker 1880 or anything else that I can Lawn Dart.
    Retired: Disco(Sold), Skywalker 1900(Dirt Nap), Qav540g/Nazav2/Iosd mk2

  3. #3
    Navigator
    Join Date
    Jun 2012
    Posts
    132
    Yes the red light is working.

  4. #4
    His Royal Sassiness ssassen's Avatar
    Join Date
    Feb 2011
    Location
    Netherlands
    Posts
    9,693
    If you applied reverse polarity to the camera as well it probably will not have survived.
    Velvety smooth drone pilot for hire

  5. #5
    Navigator
    Join Date
    Jun 2012
    Posts
    132
    No the camera is fine. I tried it on my other system.

  6. #6
    Navigator
    Join Date
    Jun 2012
    Posts
    132
    I just checked the 5V output and thats working fine. Is there a way to test the signal pin?

  7. #7
    Navigator
    Join Date
    Jun 2012
    Posts
    132
    Anyone have a clue on this? I have sent an email to Fatshark, but not heard anything yet.
    If its damaged but repairable, I'd just like to be able to send it off to be fixed asap.
    Thanks

  8. #8
    Navigator
    Join Date
    Jun 2012
    Posts
    132
    Still no joy?
    Does nobody know anything about my issue.
    Can someone please tell me where i can send it to be fixed? Or someone can verify if its dead.
    Thanks

  9. #9
    Navigator
    Join Date
    Jan 2014
    Location
    Slovenia
    Posts
    342
    Do you have a friend who can help you?

  10. #10
    Fatshark AU/NZ Repairs hpcoolahan's Avatar
    Join Date
    Nov 2011
    Location
    Yamba nsw...Australia
    Posts
    5,611
    From what you have said , you tested the camera and it still works (rule that out)
    You said had picture before ? (then the receiver in the goggles would not be affected).
    The only thing left is the TX that you applied reverse power too.
    If you have another TX/RX combo at your disposal , then try the other tx with both receivers , it it works with both of the receivers , then its got to be the TX.
    There is a repair centre in the UK that does IRC and Fatshark repairs.
    Once you figure out what's not working , you can send it in to be checked/fixed if possible.
    Australia post: "delivering packages the day after you need them since 1809"

    "Light travels faster than sound -- thats why some people appear bright until you hear them speak" - Albert Einstein.

Similar Threads

  1. 600mW 5.8GHz TX getting hot and no picture
    By uberboffin in forum ImmersionRC
    Replies: 11
    Last Post: 9th April 2014, 06:17 AM
  2. Dominator Squeezes picture?
    By taylorballam in forum Fatshark Support
    Replies: 5
    Last Post: 3rd March 2014, 01:18 PM
  3. Dominator goggles no picture right hand screen
    By smooththumbs in forum Fat Shark R/C Vision Systems
    Replies: 2
    Last Post: 26th January 2014, 05:05 AM
  4. Fat Shark Dominator loses picture after a few seconds.
    By JamesonRedding in forum Fat Shark R/C Vision Systems
    Replies: 5
    Last Post: 7th April 2013, 04:14 AM
  5. Replies: 11
    Last Post: 14th October 2012, 01:21 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •