www.immersionrc.com

Results 1 to 8 of 8

Thread: Antenna tracker audio level

  1. #1
    Navigator FinalFrag's Avatar
    Join Date
    Aug 2011
    Location
    Belgium
    Posts
    403

    Antenna tracker audio level

    I couldn't find any info online about this, so here goes.

    I've noticed that the antenna tracker audio level screen always says 'high'. The Good/Bad packet ratio is around 50%. Is this enough? The manual states that 'the tracker doesn't need a lot of good packets to work properly', but many is 'not a lot'

    I've tried with 2 different TX's (same rx) and I get about the same result. The frequency is 1360MHz.

    Is there a way to lower the audio level as an attempt to raise the ratio? In the ImmersionRC tools application there is a 'telemetry level' option for the tiny telemetry, but not for the ezosd...

    I hope there's an easy way to lower the 'volume' of the telemetry signal, even if only for perfectionist reasons :P

    The first 3 pictures are with a 300mw tx, the last one with a 400mw one.
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	foto 1.JPG 
Views:	107 
Size:	97.5 KB 
ID:	30956   Click image for larger version. 

Name:	foto 2.JPG 
Views:	85 
Size:	98.2 KB 
ID:	30957   Click image for larger version. 

Name:	foto 3.JPG 
Views:	94 
Size:	94.5 KB 
ID:	30958   Click image for larger version. 

Name:	foto 4.JPG 
Views:	86 
Size:	91.7 KB 
ID:	30959  

  2. #2
    Navigator cardboard_boks's Avatar
    Join Date
    Nov 2011
    Location
    Wellington NZ
    Posts
    891
    There is a small pot to the right of the LCD under the heatshrink, that will allow you to tune in the audio level. It is mentioned in the manual nearer the end I think.

  3. #3
    ImmersionRC Support Guru swillhide's Avatar
    Join Date
    Aug 2012
    Location
    Mountain House, Ca
    Posts
    8,443
    Or turn it down to normal. High is kinda over kill on the tracker. Before I messed with the adjustment I would adjust the osd and the tracker to normal.
    AMA # 1015480 HAM Callsign # Procrastinating..
    Futaba 9c w/Ezuhf /Skywalker 1880 or anything else that I can Lawn Dart.
    Retired: Disco(Sold), Skywalker 1900(Dirt Nap), Qav540g/Nazav2/Iosd mk2

  4. #4
    Navigator FinalFrag's Avatar
    Join Date
    Aug 2011
    Location
    Belgium
    Posts
    403

    Antenna tracker audio level

    Quote Originally Posted by swillhide View Post
    Or turn it down to normal. High is kinda over kill on the tracker. Before I messed with the adjustment I would adjust the osd and the tracker to normal.
    You cant set the audio level on the ezosd. I got it fixed with the little screw. And it was right there in the manual, can't believe i missed that.

  5. #5
    ImmersionRC Support Guru swillhide's Avatar
    Join Date
    Aug 2012
    Location
    Mountain House, Ca
    Posts
    8,443

    Antenna tracker audio level

    Your right, I was thinking telemetry data speed. Glad it's fixed.
    AMA # 1015480 HAM Callsign # Procrastinating..
    Futaba 9c w/Ezuhf /Skywalker 1880 or anything else that I can Lawn Dart.
    Retired: Disco(Sold), Skywalker 1900(Dirt Nap), Qav540g/Nazav2/Iosd mk2

  6. #6
    Navigator cardboard_boks's Avatar
    Join Date
    Nov 2011
    Location
    Wellington NZ
    Posts
    891
    And it was right there in the manual, can't believe i missed that
    That is an intense manual, I had to read it through at least twice to ingest all the information.

  7. #7
    Navigator
    Join Date
    Jul 2013
    Posts
    183

    EZTRACKER Showing high volume

    Hi,

    I have the eztracker unit and before i plug anything in the audio is high and when receiver audio is plugged in it goes to ok is it normal to be high without anything plugged in thought it should be low

    thanks

  8. #8
    ImmersionRC Support Guru swillhide's Avatar
    Join Date
    Aug 2012
    Location
    Mountain House, Ca
    Posts
    8,443
    If there is no impedance in the line for the tracker to gauge then its gonna show high. Nothing wrong with it, go flying.
    AMA # 1015480 HAM Callsign # Procrastinating..
    Futaba 9c w/Ezuhf /Skywalker 1880 or anything else that I can Lawn Dart.
    Retired: Disco(Sold), Skywalker 1900(Dirt Nap), Qav540g/Nazav2/Iosd mk2

Similar Threads

  1. tiny telemetry too low audio level?
    By maxjos in forum ImmersionRC
    Replies: 9
    Last Post: 13th August 2013, 10:48 PM
  2. vTx audio - line level input??
    By BCSaltchucker in forum Power Regulation / Power Distribution
    Replies: 3
    Last Post: 25th March 2013, 02:10 PM
  3. Audio Levels issue on Antenna Tracker
    By deviant in forum ImmersionRC
    Replies: 19
    Last Post: 3rd September 2012, 10:17 AM
  4. DUO 2400 Low Audio FOR EZ TRACKER
    By topwaxer in forum ImmersionRC
    Replies: 1
    Last Post: 5th April 2012, 09:20 AM
  5. Splitting Audio to EZ tracker and iPhone
    By DIGITAL_DARKSIDE in forum ImmersionRC
    Replies: 1
    Last Post: 28th October 2011, 02:38 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •