FPVLAB

image
Results 1 to 5 of 5

Thread: Throttle mod for Taranis Tx

  1. #1
    Navigator BrunoBL's Avatar
    Join Date
    Jul 2014
    Location
    Santa Catarina, Brazil
    Posts
    328

    Throttle mod for Taranis Tx

    Hi Guys,

    Here is a mod to create a half-throttle notch in the Taranis Tx throttle stick movement. This provides both a tactile feedback and a positive hold for the half-throttle position, even when moving the stick about its yaw axis which of course can be overcome with minimum effort when increasing or decreasing throttle from its mid-point position. The result feels much like the center notch on the potentiometers and sliders on the Taranis radio.


    The mod was inspired by Phantom transmitters that have the throttle spring-loaded to center which is a good idea for multicopters but impractical for fixed-wing flying. A half-throttle notch attempts to provide a solution for both multicopters and fixed-wing models, with no need for mechanical adjustments to the Tx when switching between those model types.


    Here is how to do it:


    - Remove the double metal strip that provides the throttle with both friction and ratchet movement. it is actually two springs in one, joined at the bottom end. Using a Dremel cutting wheel, separate them from each other. Take care not to cut through the holes - a thin cutting wheel such as Dremel #409 worked perfectly. Only the half-spring with the "V" bend will be used. The image below shows the springs already separated:

    Click image for larger version. 

Name:	Separated Spring.jpg 
Views:	21 
Size:	324.0 KB 
ID:	79095



    This is the tricky part:

    - Move the stick to EXACTLY half-throttle position and make sure it stays there during the next two steps.

    - Attach the "V"-bend spring to the position that used to belong to its straight counterpart (i.e, it's "V" bend tip will now ride on the smooth, non-ratcheted friction surface). Note where the "V" tip touches the smooth surface, mark it very precisely and then remove the spring.

    - With the spring out of the way: using an X-ACTO knife or similar tool, cut a single groove on the smooth (non-ratcheted) surface on the position found on the earlier step. It is critical that the throttle is exactly on its mid-way position and also that the groove is cut precisely under the point where the "V" bend touches the friction surface, as this will mechanically define the half-throttle detent position. For your reference, the groove should be as small and shallow as the neighboring ratchet grooves (in fact, I made it even smaller and shallower). The image below shows the groove cut into the smooth friction surface:

    Click image for larger version. 

Name:	Half-Throttle Groove.jpg 
Views:	23 
Size:	290.2 KB 
ID:	79093



    - Reattach the spring and adjust tension as desired. On the image below, note that the ratcheted surface has no longer a spring riding on it, and the "V" spring is riding on the smooth surface:
    Click image for larger version. 

Name:	Spring on Smooth Surface with One Groove.jpg 
Views:	24 
Size:	257.5 KB 
ID:	79094



    You will find that you now have a non-spring-loaded throttle with a single "clicked" detent at exactly half-throttle, perfect for flying multirotors and airplanes with no-fuss model changing.

    Hope this is useful for anyone.
    Last edited by BrunoBL; 27th July 2019 at 04:58 PM. Reason: Images re-uploaded

  2. #2
    Navigator
    Join Date
    Aug 2018
    Posts
    1
    Thank you, very interesting
    But the pictures are gone !!

  3. #3
    Navigator
    Join Date
    May 2012
    Posts
    102
    Great idea!

  4. #4
    Navigator BrunoBL's Avatar
    Join Date
    Jul 2014
    Location
    Santa Catarina, Brazil
    Posts
    328
    I don't know what happened to the pictures, but anyway I re-uploaded them.
    Hope this makes the mode clearer.

  5. #5
    Navigator
    Join Date
    Mar 2017
    Posts
    28
    Thank you, very nice

Similar Threads

  1. Replies: 11
    Last Post: 28th February 2015, 02:33 AM
  2. Rig the LEDs to Throttle?
    By the.ronin in forum Power Regulation / Power Distribution
    Replies: 13
    Last Post: 14th January 2015, 10:00 AM
  3. Replies: 2
    Last Post: 5th January 2015, 04:25 PM
  4. Throttle mush :(
    By Zerosink in forum Team-Black Sheep
    Replies: 7
    Last Post: 1st December 2013, 05:11 AM
  5. Throttle/Elevator
    By Bandarra in forum RC TECH
    Replies: 3
    Last Post: 12th October 2011, 03:23 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •