image

Search:

Type: Posts; User: Beachflyer; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.03 seconds.

  1. I'll spend some time this weekend working on...

    I'll spend some time this weekend working on another setup using Crossfire and Futuba 14. I'll let you know if I get it working with 12 channels.
    Question, are you using sbus or ppm?
  2. You get an attaboy Doobie! Of course it takes a...

    You get an attaboy Doobie! Of course it takes a thousand attaboys to make up for one Oh Sh&t!;)
  3. 71815JONO, Did you do this?

    71815JONO,
    Did you do this?
  4. ^LMAO

    ^LMAO
  5. https://pixhawk.org/firmware/start Maybe this...

    https://pixhawk.org/firmware/start
    Maybe this will help on second question.
  6. I have a second RX. I'll try it on 1.20 first and...

    I have a second RX. I'll try it on 1.20 first and if I have same results I will go with 1.09. May take a little time to test the variations but I will report back.
    Thanks for the input. I'll get a...
  7. Everyday brings a new adventure. No failsafe...

    Everyday brings a new adventure. No failsafe today that I noticed. But 15-20 minutes into a run and 150 yards away my video blanked out. What the hell does that have to do with the Xfire? Nothing, I...
  8. PERNA: Here is the exact mapping for the 8...

    PERNA:
    Here is the exact mapping for the 8 channels.
  9. Tx is Futaba 14SG Input set to Futaba 12 channel...

    Tx is Futaba 14SG
    Input set to Futaba 12 channel
    Output mapping is:
    Ouput 1 CH1
    thru
    Ouput 8. CH8

    One other issue:
    I have a 3 cell external battery connected to Xfire.
    I get the red...
  10. Perna, Saw your post after I posted my last...

    Perna,
    Saw your post after I posted my last post. Maybe it answers most of your questions.
    i assume by Version you mean firmware version. It is 1.20.
  11. This may be a common occurrence or "normal" if...

    This may be a common occurrence or "normal" if you will.
    I have never noticed this while flying with Xfire. However I've always used PPM output to FC.
    I now have a Xfire Diversity RX on my Summit...
  12. I have to power cycle my RX and then I regain the...

    I have to power cycle my RX and then I regain the higher channels. This happens everytime I have a failsafe.
    Took a while to figure out and still do not understand why the loss of control between...
  13. I've had a similiar experience. Question though,...

    I've had a similiar experience. Question though, when you got back closer to home did you regain the use of the higher channels?
  14. Read back a couple of pages.

    Read back a couple of pages.
  15. Thanks, Slappo Noticed that today and checked...

    Thanks, Slappo
    Noticed that today and checked manual but didn't see a definitive answer.
    Had 2 failsafes close in and checked and I was only Tx at 100mw.
  16. If you turn the telemetry off on the Xfire does...

    If you turn the telemetry off on the Xfire does it effect the dynamic switching?
  17. Problem solved! Ran for an hour today with no...

    Problem solved! Ran for an hour today with no problem.
  18. This might help:...

    This might help: http://team-blacksheep.freshdesk.com/support/solutions/articles/4000071530-12-channel-mode-with-futaba
  19. Think I know what was going on. There was a known...

    Think I know what was going on. There was a known problem using the 14SG thru the trainer port. Changed setting in radio to 12 channel ppm. See if this helps today.
  20. Any ideas? Guess I'll hook the Blackbox up and...

    Any ideas? Guess I'll hook the Blackbox up and see what it captures.
  21. Take a picture of the pins at the back of the top...

    Take a picture of the pins at the back of the top plate and I can tell you for sure how to connect.
    Here are a couple of pics that may help.

    7104871049
  22. Connect ch1 of your XF RX to the #1 pin on the...

    Connect ch1 of your XF RX to the #1 pin on the top plate. Connect XF ch7 and 8 on pin 7 and 8. Since you are using the XF Futaba cable connected your Tx, you will use ppm. You would only use subs if...
  23. Ok, strange stuff going on with my Crossfire....

    Ok, strange stuff going on with my Crossfire. Have the Xfire on a newly constructed ground pounder. I already had the Xfire with a diversity RX on a quad. Had no problems on the quad with the...
  24. 70939Jschaer, Check this pin on your antenna....

    70939Jschaer,
    Check this pin on your antenna. Make sure it is protruding about 1/4".
  25. Sweet!

    Sweet!
Results 1 to 25 of 29
Page 1 of 2 1 2