image

Search:

Type: Posts; User: Torchwork; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.03 seconds.

  1. Replies
    40
    Views
    23,924

    Sticky: A substantial amount of funds should go into...

    A substantial amount of funds should go into marketing the amazing FUFAA quad!
  2. I would imagine you could lower the settings in...

    I would imagine you could lower the settings in angle or horizon mode to not auto level very much, if any. The attitude is the angle of the craft. You can also set angle limits.
  3. Ok. I reformatted the card, multiple times in my...

    Ok. I reformatted the card, multiple times in my computer and it still wouldn't work, but after reformatting the card in my cannon dslr it works. Stoked
  4. I have tried two formatted cards so far. One was...

    I have tried two formatted cards so far. One was brand new. If they don't work, I'll send it to the address you provided.
  5. Just shot you an email for a similar problem. My...

    Just shot you an email for a similar problem. My dvr doesn't work, but the light doesn't come on except for startup.
  6. Mmi have mine heat shrinked with the pins coming...

    Mmi have mine heat shrinked with the pins coming over the board for a low profile setup. All my wires come out in one direction. Never had cooling issues and I've had it stuffed deeper in the mix...
  7. How bad are the pads coming off? Once everything...

    How bad are the pads coming off? Once everything is soldered you can use epoxy or clear nail polish. Have separated your rtx a few feet away during this rssi jumping around? I've read in other...
  8. have you tried port 2 (rssi w/ppm enabled) and...

    have you tried port 2 (rssi w/ppm enabled) and ground off the rx into the rssi on the osd? And enabled in the gui?
  9. Try grounding separately. I only have Vout...

    Try grounding separately. I only have Vout grounded and mine quit flickering.
  10. I have the exact same setup, but I don't use lux....

    I have the exact same setup, but I don't use lux. Pretty sure your PIDs should be at least half that. My PIDs aren't that high and I use controller 3. Let me know what you end up with, I'll try lux...
  11. I had the same problem. Pretty sure you need to...

    I had the same problem. Pretty sure you need to change the com port on the computer settings, not in the gui. It's misleading because you can get all the read/write stuff green without anything...
  12. When I try to flash the firmware the config.h no...

    When I try to flash the firmware the config.h no such file stops the load. What do I need to change in the code?
  13. Replies
    23
    Views
    29,773

    Did you ever get chirping or sync issues on those...

    Did you ever get chirping or sync issues on those escs? I've tried the fix with the long beeping process.
  14. Replies
    8
    Views
    1,743

    Efficiency for racing? What kind of racing.

    Efficiency for racing? What kind of racing.
  15. Replies
    8
    Views
    1,743

    Have you found an inexpensive prop source? So far...

    Have you found an inexpensive prop source? So far I have only found 5045 for about .50 a piece and .75 for the 6045.
  16. Replies
    8
    Views
    1,743

    Same here. I just bought some 2000kv Cobras, but...

    Same here. I just bought some 2000kv Cobras, but I think I'll crash a few times and get the 2700kv next.
  17. Replies
    0
    Views
    774

    CleanFlight | failsafe with hitec

    Im trying to setup failsafe with my aurora 9, and it seems like all the settings go where they should when I look with cleanflight, but the motors stop immediately. I have failsafe disabled in...
  18. Dialing in my PIDs and having some fun but I'm...

    Dialing in my PIDs and having some fun but I'm not sure what to do on this one. Front flips are super fast, so are the right rolls. Backflips are quick, but left rolls are the slowest. I have...
  19. Replies
    13
    Views
    9,256

    Mine flies fairly smooth without changing the...

    Mine flies fairly smooth without changing the settings in angle mode. It's not quick enough to do flips in rate mode though, which will change soon.
  20. Replies
    20
    Views
    5,875

    ConradM, where do you get your 5045s?

    ConradM, where do you get your 5045s?
  21. Replies
    11
    Views
    6,705

    That makes sense. Is that what causes the extreme...

    That makes sense. Is that what causes the extreme fisheye views? I'm looking to get goggles soon, not sure if I'll use the gopro.
  22. Replies
    749
    Views
    87,572

    Poll: KM4HKX. Got mine after seeing a quadcopter racing...

    KM4HKX. Got mine after seeing a quadcopter racing video over Christmas. I hadn't realized the rc world had progressed so much. Thank you IBCrazy!
  23. Replies
    8
    Views
    2,249

    I'm building first setup as well. I got a BEC...

    I'm building first setup as well. I got a BEC since my receiver voltage limit is around 7 volts. Mine came with a ferrite ring which supposed to help with interference. What other accoutrements are...
  24. Replies
    24
    Views
    13,901

    it would be nice to be able to design some...

    it would be nice to be able to design some business uses around these things without too much hassle. A license is all it needs. Just like selling liquor.
  25. Replies
    22
    Views
    3,181

    Still flying in chas? I'm building a quad right...

    Still flying in chas? I'm building a quad right now and just got the HAM license.
Results 1 to 25 of 36
Page 1 of 2 1 2