image

Search:

Type: Posts; User: hodges42; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.02 seconds.

  1. Replies
    1
    Views
    1,904

    Gatling 2.4 or 1.3

    I have a question about video quality at range. When i was attempting long range for me, roughly 5 miles (fixed wings) I only made it to 3 and thats where I stayed no matter what I did that was the...
  2. Thread: 2.4ghz gear

    by hodges42
    Replies
    37
    Views
    3,938

    Antenna selection

    I have the following items: What VTX antenna would you recommend?

    SpiroNet 2.4GHz Patch Antenna RHCP
    Duo2400v3 A/V Diversity Receiver
    700mW 2.4GHz audio/video transmitter, US Version
  3. Replies
    697
    Views
    162,182

    Sticky: Can the pepper box, helical or a directional...

    Can the pepper box, helical or a directional patch antenna be used to transmit video and if so do you think there would be a benefit over an omni antenna.
  4. Replies
    11
    Views
    1,065

    Anymore suggestions. Thanks

    Anymore suggestions.
    Thanks
  5. Replies
    5
    Views
    839

    For some reason air mode became disabled, I have...

    For some reason air mode became disabled, I have configured to a switch so when acro is activated air mode is also.
    Thanks
  6. Replies
    2
    Views
    780

    78040okay this is showing on both my 150 s. I...

    78040okay this is showing on both my 150 s. I have not found where to disable it. Thanks
  7. Replies
    5
    Views
    839

    Im running 700mah 75c packs and air mode was off....

    Im running 700mah 75c packs and air mode was off. Thanks.
  8. Replies
    5
    Views
    839

    Vortex 150 batteries

    When running at WOT and > 14 volts and around 25 amps my 150 starts to roll or yaw due to lack of battery power. Just wondering what batteries are being used before purchase? Thanks
  9. Fatshark - 1800mAh 7.4v Battery Pack USB Charging

    Fatshark - 1800mAh 7.4v Battery Pack USB Charging red LED Indicator flashes rapidly and continuously when not in use.
  10. Replies
    170
    Views
    25,841

    deleted

    deleted
  11. Replies
    1
    Views
    2,679

    deleted

    deleted
  12. Replies
    1
    Views
    2,679

    Acceptable battery sag

    deleted
  13. Replies
    11
    Views
    1,065

    Deleted

    Deleted
  14. Replies
    2
    Views
    780

    Vortex 150 RSSI on OSD screen

    Recently the RSSI from my Taranis started showing up on my osd and it somehow is tied to a switch that is use for the timer. In on position it show a low RSSI and in the other position it shows...
  15. Replies
    5
    Views
    634

    What brand of blades are you running and are they...

    What brand of blades are you running and are they durable?
    Thanks.
  16. Replies
    11
    Views
    1,065

    Flight controller secured and connections are...

    Flight controller secured and connections are good.
  17. Replies
    11
    Views
    1,065

    installed 4 new 5040 bull nose props with same...

    installed 4 new 5040 bull nose props with same results. ckd the shafts and found no negative results. Installed new props and used a ruler to ck the track of the blades.
    Thanks
  18. Replies
    11
    Views
    1,065

    on a fresh pack it'll usually go to 14 , but even...

    on a fresh pack it'll usually go to 14 , but even when I'm hovering at around half throttle and I go to increase throttle slightly you'll hear and see the quad kind of shutter, not nearly as bad as...
  19. Replies
    11
    Views
    1,065

    4s Tattu 1300 mah 75c

    4s Tattu 1300 mah 75c
  20. Replies
    11
    Views
    1,065

    Vortex pro 250 throttle up

    I have been flying the vortex for a couple of weeks now and no matter what preset tune I use , when i go above half throttle or especially a punch out it sounds like the motors are rapidly cutting...
  21. Thread: Dominator V1

    by hodges42
    Replies
    0
    Views
    448

    Dominator V1

    My dominator center board has a loose connection somewhere and I cant seem to find it. Is it possible to order the upper center circuit board. The board has a date of May 2011 if that helps.
    Thanks
  22. Replies
    4
    Views
    729

    Got it , Thanks

    Got it , Thanks
  23. Replies
    4
    Views
    729

    Thank You

    Thank You
  24. Replies
    4
    Views
    729

    Vortex 150 Camera Hardware

    What are the sizes of the 2 upper hex head screws that secure the camera angle?
    Thanks
  25. Replies
    3,703
    Views
    408,430

    1. Download your vector and ck your rssi to see...

    1. Download your vector and ck your rssi to see if it is signal loss and ck your notifications for anything strange.
    2. ck the wiring going into the vector (input - outputs) . Had a copter...
Results 1 to 25 of 36
Page 1 of 2 1 2