image

Search:

Type: Posts; User: OhmEye; Keyword(s):

Page 1 of 12 1 2 3 4

Search: Search took 0.07 seconds.

  1. Thread: Frsky Taranis

    by OhmEye
    Replies
    849
    Views
    159,219

    The place I got mine shows them in stock,...

    The place I got mine shows them in stock, multirotorsuperstore.com
  2. wow. I use a 10mw 5G8 VTX for my repeater. 600mw...

    wow. I use a 10mw 5G8 VTX for my repeater. 600mw is major overkill for going a few feet! :) Fatshark sells a 25mw if you use that stuff. I use a $9 10mw boscam module.
  3. I use only the signal wires on all my ESCs and...

    I use only the signal wires on all my ESCs and power everything from a dedicated BEC. I remove the ground and 5v wires (red and black.)
    ...
  4. Replies
    3,736
    Views
    541,513

    1) Yes, airplane and wing mixers are in main...

    1) Yes, airplane and wing mixers are in main baseflight. For RTH and PH modes there is a forked version that I believe will be merged into the main at some point.
    2) RTH and PH are reportedly...
  5. Replies
    1,058
    Views
    276,204

    I compare actual current measured with a current...

    I compare actual current measured with a current meter to the displayed OSD current and adjust until they match.
  6. As long as the version of SimonK on the ESC isn't...

    As long as the version of SimonK on the ESC isn't ancient, it can likely be flashed using a USB linker. If not, then using pads on the ESC or a chip clip with a ISP programmer should always work.
    ...
  7. Ah. SimonK isn't programmable like most stock...

    Ah. SimonK isn't programmable like most stock firmware, no runtime configuration like people may expect with a programming card. I'm sure it's flashable, just use a USB linker and RapidFlash chrome...
  8. What do you mean by not flashable? What is...

    What do you mean by not flashable? What is stopping you from flashing them?
  9. Micro USB is rated for many more plug/unplug...

    Micro USB is rated for many more plug/unplug cycles than mini, if I recall. Plus since the EU mandated micro for all cell phones 3 years ago, it's pretty much everywhere now.
  10. PID is the tuning for how well it controls...

    PID is the tuning for how well it controls attitude, when tuned well it doesn't over/undershoot resulting in oscillations. If you aren't having oscillations, you probably don't need to touch PID....
  11. I'm confused. Are you having problems with PID or...

    I'm confused. Are you having problems with PID or throttle?
  12. Thread: Frsky Taranis

    by OhmEye
    Replies
    849
    Views
    159,219

    Yes. The Rhino has 3 plugs on it already, I just...

    Yes. The Rhino has 3 plugs on it already, I just replaced one I have no use for with a balance plug using the same polarity as the supplied NiMH.

    Lipo TX packs are higher capacity for the size...
  13. Thread: Frsky Taranis

    by OhmEye
    Replies
    849
    Views
    159,219

    It's a standard 2s balance plug but check the...

    It's a standard 2s balance plug but check the polarity, yes.
  14. Thread: Frsky Taranis

    by OhmEye
    Replies
    849
    Views
    159,219

    My vote also for the Rhino 3S 2620 TX batt. My...

    My vote also for the Rhino 3S 2620 TX batt. My Taranis came with the NiMH 800, I replaced with the NiMH LSD 2000 but hadn't replaced the internal charger circuit and didn't like the voltage discharge...
  15. Are you using PWM or PPM for RX to naze? Does...

    Are you using PWM or PPM for RX to naze? Does naze configuration match the RX wiring? (And 20A BEC! WOW! how big is that servo?!?)
  16. 5v, GND, TX, RX

    5v, GND, TX, RX
  17. Thread: KV OSD

    by OhmEye
    Replies
    1,599
    Views
    323,663

    Fonts did not upload. If you have the analog and...

    Fonts did not upload. If you have the analog and digital sides power connected, make sure you are supplying 5v power, not 3.3v or something. If you don't have the sides connected, connect them. The...
  18. What do you mean by "busted ground wire"? What...

    What do you mean by "busted ground wire"? What actually happened? I don't even use a wire on my VBAT GND input.
  19. Do you have an OSD connected via serial?

    Do you have an OSD connected via serial?
  20. Thread: Frsky Taranis

    by OhmEye
    Replies
    849
    Views
    159,219

    I'm going in circles trying to get opentx 2.04...

    I'm going in circles trying to get opentx 2.04 flashed. Using today's release on companion on linux, I can read and write models/settings/backups fine, but not firmware. No progress bar or errors,...
  21. Thread: Frsky Taranis

    by OhmEye
    Replies
    849
    Views
    159,219

    Any known issues or bugs with v2 yet?

    Any known issues or bugs with v2 yet?
  22. Excellent! I never noticed that, very nice.

    Excellent! I never noticed that, very nice.
  23. Sure. Or flip the right angle header around so...

    Sure. Or flip the right angle header around so it's over the board. Or don't use headers at all and solder direct. Or solder any type of pigtail connector you like.


    Horizon is kind of a blend....
  24. Replies
    3,736
    Views
    541,513

    Is anybody taking on the effort to do whatever...

    Is anybody taking on the effort to do whatever cleanup or changes are needed to get the RTH code accepted into the main repo? I've only just started looking through the code.
  25. Replies
    3,736
    Views
    541,513

    So RTH mode can't be combined with altitude hold...

    So RTH mode can't be combined with altitude hold to maintain altitude? Or does RTH mode do it's own version of altitude hold and so they conflict if both enabled? Seems to me RTH is useless without...
Results 1 to 25 of 289
Page 1 of 12 1 2 3 4