image

Search:

Type: Posts; User: malibu73; Keyword(s):

Search: Search took 0.05 seconds.

  1. Replies
    10
    Views
    1,366

    I currently have the servo wires in both booms...

    I currently have the servo wires in both booms and the camera sharing the right. They are aluminum so no help there either. Thanks
    This isn't my first plane, but you may be right about the fate of...
  2. Replies
    10
    Views
    1,366

    76381 OK, sorry to be so dense about this, but...

    76381

    OK, sorry to be so dense about this, but the camera will be mounted at the top of the V tail, the Dragon link antenna on far wing tip and everything else in the fuse. So would I be OK not to...
  3. Replies
    10
    Views
    1,366

    Yeah, I'm working my way through that thread. I'm...

    Yeah, I'm working my way through that thread. I'm just trying to figure out if its important to shield the camera and which side to leave the ground floating at.
    ...
  4. Replies
    10
    Views
    1,366

    I'm going to be running an arkbird osd and mostly...

    I'm going to be running an arkbird osd and mostly following this diagram. https://hobbyking.com/media/file/676532010X414570X51.jpeg

    The wiring for my camera will be probably about 4 foot long....
  5. Replies
    10
    Views
    1,366

    Ok, thanks. I like the idea of midway mounting...

    Ok, thanks. I like the idea of midway mounting the VTX, less wires overall if i'm picturing it correctly. Approximately how much space does the GPS need from the vtx antenna? Is motor Proximity an...
  6. Replies
    10
    Views
    1,366

    Large FPV Wiring

    I'm building the Hobby King rq-7 Shadow 2000mm and want to do some kind of FPV.
    I'm using 2.4ghz Immersion VTX with a circular polarized antenna and want to put that antenna out on one of the wings...
  7. Replies
    865
    Views
    151,809

    I gave up, I wired 5 volts and 12 volts from...

    I gave up, I wired 5 volts and 12 volts from another source and got some magic white smoke. I think my career in electronics repair is over. I guess I was lucky to get it to work as long as it did.
  8. Could it be repaired? Dianmu Main OSD Board

    Any help rebuilding the main board?

    A couple years ago the plug that was attached to the main board that goes to the current sensor came un-soldered. Most of the pad separated form the board...
  9. Replies
    865
    Views
    151,809

    thats what i did originally, but it finally...

    thats what i did originally, but it finally stopped working the other night. Any ideas where I can solder to? I don't know that much about PCB boards and was hopping someone could give me some...
  10. Replies
    865
    Views
    151,809

    Any help rebuilding the main board? A couple...

    Any help rebuilding the main board?

    A couple years ago the plug that was attached to the main board that goes to the current sensor came un-soldered. Most of the pad separated form the board...
  11. Replies
    0
    Views
    1,575

    Erratic Channels on Receiver?

    I noticed this last year when flying that the channels were acting erratic. Started to get everything out again this year and still, having the issue. I thought it was a short at the dragon link...
  12. Scratch all that. I had the two plugs in the...

    Scratch all that. I had the two plugs in the bottom picture switched. Problem solved.
  13. Plane Crashed in Lake Dianmu OSD Soaked What to replace?

    I have a small problem. I recently installed my Dianmu in my sky surfer and everything was working perfect until it wasn't. My receiver went out and I crashed in to the river....
    Well when we pulled...
  14. Replies
    865
    Views
    151,809

    I have a small problem. I recently installed my...

    I have a small problem. I recently installed my Dianmu in my sky surfer and everything was working perfect until it wasn't. My receiver went out and I crashed in to the river....
    Well when we pulled...
Results 1 to 14 of 14