image

Search:

Type: Posts; User: gencode; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    653

    Putting the foam pad behind the module made the...

    Putting the foam pad behind the module made the module always pop out and did not help my up command on the 4 way knob issue. I cut the foam and put it right underneath the display, now I am now...
  2. Replies
    5
    Views
    653

    I have removed several times, placed back in...

    I have removed several times, placed back in firmly and flush then put door back on firm and flush, result is the same.
  3. Replies
    5
    Views
    653

    Rapid fire door does not fit well

    My rapid fire door does not fit well. The knob wont move up when the door is on. The entire hole seems off center and its a pretty big disappointment because at first I thought the knob was broke. ...
  4. TBS Mini with uBlox GPS on KISS V2 - Is there a way to get coordinate Telemetry?

    I have a TBS Mini with uBlox GPS on KISS V2 - Is there a way to get coordinate Telemetry back to the Taranus with these?
    https://www.racedayquads.com/products/micro-ublox-m8n-gps-glonass

    I know...
  5. Blue LED only - TBS Unify Pro V3 - Poor range

    I am only getting about 100 feet before I get to much static to fly.
    My light is blue only is that right? Reading the manual it seems as if it should be red and blue?
    Deactivate: ​press...
  6. Tramp HV +5V Out - Whats the max amp draw it can handle? 600mw? 1w?

    Tramp HV +5V Out - Whats the max amp draw it can handle? 600mw? 1W?

    I want to power my RunCam Split Cam from it so if it can handle 1W that would work.

    Thanks, Ed,
  7. Replies
    5
    Views
    1,532

    The new one came in, issue resolved, fantastic...

    The new one came in, issue resolved, fantastic video.
    Got it setup on the switch too for power high and low, works great.

    Just a note, the old bad one had a black dot, new good one does not, does...
  8. Replies
    5
    Views
    1,532

    ...thanks!

    ...thanks!
  9. Replies
    5
    Views
    1,532

    I made a little clip of my issue. ...

    I made a little clip of my issue.

    https://www.youtube.com/watch?v=GvUMq-XCNqw
  10. Replies
    5
    Views
    1,532

    Noise lines in my tramp hv

    I am getting lines in my Tramp HV.
    I have rewired, used battery pack direct.
    It happens when no motors running so its not ESC feedback

    Any suggestions?
  11. Thanks, never noticed it there :)

    Thanks, never noticed it there :)
  12. Can I Turn off telemetry that comes thru Audio (left speaker)

    Can I turn off telemetry that comes thru Audio (left speaker for me)

    I am asking because I hooked up audio and it works, but there is still some of the telemetry sounding bleeding thu to my right...
  13. Replies
    1
    Views
    581

    Set battery voltage alarm per cell

    Is there a way to set the battery alarm, I feel its too low and my batteries are getting puffy, I want to adjust it a little to the alarm goes off sooner to remind me to land.
  14. Replies
    2
    Views
    1,925

    This was solved, I had the wires incorrect, but...

    This was solved, I had the wires incorrect, but it would be nice to turn off the telemtry noise as its even bleeding to my other speaker a little
  15. Replies
    2
    Views
    1,925

    Adding sound/mic with Vortex Pro/Fatshark

    I read this about adding a mic
    http://www.immersionrc.com/adding-a-microphone-to-the-vortex-250/

    So I added one, hooked my camera mic to AL of CN9 like the diagram (power is not connected as its...
  16. Replies
    0
    Views
    639

    Earbuds distort picture in Dominator V3

    When I plug in the earbuds the pic gets distorted.When I unplug the headphones picture corrects
    UPDATE: Sorry, apparently there are 2 headphone looking jacks, I was using the video one, headphones...
  17. Yup, great too. I got the GoPro power plug and...

    Yup, great too.
    I got the GoPro power plug and am using that now for the camera power instead of the PPM Rx power
    I only needed to solder 1 wire to the board.
  18. Thanks for the quick feedback. Please add to...

    Thanks for the quick feedback.
    Please add to wish list for next version of Vortex/Fusion board as its common now days in F3 FC.
  19. Is there any way to get the telemetry output like on most f3 flight controllers

    Is there any way to get the telemetry output like on most f3 flight controllers with the fusion board, I want to send it to the taranis from the vortex pro 250.
    Basically my FRSKY has telemetry...
  20. Is there a diagram on what plug goes to what Rx for Vortex Pro

    Is there a diagram on what plug goes to what Rx for Vortex Pro?

    I have a Spektrum Rx serial but I broke my Tx and while its in the shop I want to use my Tarinus CPPM/SBUS
    What port on the Fusion...
  21. Connected it this way, works great and only one...

    Connected it this way, works great and only one solder to pins needed.
    73095
  22. Why not just use the 5V for the camera from one...

    Why not just use the 5V for the camera from one of the unused Rx Plugs like GoPro Power Plug, SBUS or Spektrum or whatever your not using to power the camera?
    Then you only need to solder on one of...
  23. Replies
    7
    Views
    1,015

    Is the connector soldered on or is the clamp on...

    Is the connector soldered on or is the clamp on the sides just "holding it on" to make the connection with pressure points?

    I found another thread where they said we can use these points. Seems a...
  24. Replies
    7
    Views
    1,015

    Dang, I don't want to change my entire PDB, are...

    Dang, I don't want to change my entire PDB, are there alternative solder points on the board or the VTx I can just solder to without removing the PDB?
    Please say yes :D
  25. Replies
    7
    Views
    1,015

    Nevermind, I wiggled the front cam connector and...

    Nevermind, I wiggled the front cam connector and it comes on and off, guess it needs video to see the OSD. I am not sure why they moved that connector to the front in a spot behind the camera that...
Results 1 to 25 of 148
Page 1 of 6 1 2 3 4