image

Search:

Type: Posts; User: andy120; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Thread: Anaconda

    by andy120
    Replies
    0
    Views
    1,124

    Anaconda

    Do you have replacement lower nose assemblies in stock?
  2. Replies
    3
    Views
    467

    Ok sorted it. It had to be reflashed when plugged...

    Ok sorted it. It had to be reflashed when plugged into but not 'connected' to the pc.
  3. Replies
    3
    Views
    467

    Yes. I got it to load somehow with the flash page...

    Yes. I got it to load somehow with the flash page set to wipe and reflash on connection.
  4. Replies
    3
    Views
    467

    Cleanflight help

    Im new to FC's. I have installed CF config on chrome but i only have the CLI. How do i get the GUI?
  5. Replies
    0
    Views
    687

    Non warranty repair

    Hi
    I have a 600mW 5.8g Tx on which i has blown the +ve capacitor from a short. Can you repair it?

    Andy
    NZ
  6. Replies
    1,229
    Views
    505,230

    Hi, I've read most of this thread. I think it...

    Hi, I've read most of this thread. I think it would be helpful for people trying to pick a coupler if a basic list could be made giving the most suited Narda and mini-circuits couplers for each of...
  7. Replies
    1
    Views
    1,640

    800mW VTx antenna

    I have the int'l version of the 800mW 900MHz transmitter. I want to change antennas to a full wave dipole. Can I replace the stock one with a straight sma with the elements directly attached or do i...
  8. Here there was zero consultation with joe public...

    Here there was zero consultation with joe public flyers that i heard of. It sounds like model flight nz probably were and for there own interest made themselves part of that law by pretty much...
  9. Same BS going on in New Zealand too.

    Same BS going on in New Zealand too.
  10. Replies
    3
    Views
    1,629

    Turns out that you need some sort of ppm flight...

    Turns out that you need some sort of ppm flight controller like pixhawk. That will take 4+ channels off a single rx pin leaving the rest of the pins for channels 9+.
  11. Replies
    0
    Views
    370

    Orangerx futaba modules

    HK has 3 different futaba modules listed. Whats the difference?
    I see there have been issues with orangerx, is spektrum a more reliable option?

    Andy

    edit
    Different protocols available.
  12. Replies
    1
    Views
    621

    OSD Pro and 12v power

    Hi
    Can OSD Pro tolerate 12v applied to the Video in/out ports? I have a 12v VTx with a 5v camera.

    Andy
  13. Replies
    3
    Views
    1,012

    Got it. Zero interference. Andy 66009

    Got it. Zero interference.
    Andy
    66009
  14. I'm in for an attitude pair if you are going to...

    I'm in for an attitude pair if you are going to do them.
    Andy
  15. Replies
    3
    Views
    1,012

    Everything is well and truly buried. this is the...

    Everything is well and truly buried. this is the wiring i used. left 12-ish volts, right split 5/12v.
    65898

    andy
  16. Replies
    3
    Views
    1,012

    RMRC Tx and FS cameras

    Hi
    I have a 900mhz Tx (which runs 12v for camera system) and a FS 5.8G system. I am trying to run my FS 600tvl thru the 900mhz Tx. The spec sheet says up to 5v for the camera, but with a 5v supply...
  17. Replies
    2
    Views
    750

    Video filter placement

    Hi
    To fix the lines on my video (900MHz) im going to put a 6 turn toroid in the video line and a filter (RMRC LC) in the Tx power supply (battery all its own). Where should the toroid go in the food...
  18. Replies
    0
    Views
    581

    antenna orientation

    Hi
    I have a stock 900mhz video system with omni's. I want to go for height fairly close to directly above me. Should i lay the Rx and Tx antennas parallel to the ground to avoid the null zones? Will...
  19. Replies
    3
    Views
    1,629

    access to channels 9+

    I have an 8 channel Tx and the 8 output mini Rx. With a head tracker connected, how to i access channels 9 & 10 if i'm using all 8 Rx outputs on the Tx for flight servos? Do i need a S-bus adapter in...
  20. Sticky: Futtaba 8u

    Hi all.
    I had head tracking working about a year and a half ago on a different model but havent been able to replicate is functionality.
    I have trainer enabled to 'func' on channels 7 & 8 and my...
  21. Replies
    1
    Views
    453

    Trinity channel expansion

    Are there any plans to extend the channels available for trinity to use ie 9-11?

    Thanks
    Andy
  22. Sticky: Anyone had any luck with a Futaba 8UAPS? Found...

    Anyone had any luck with a Futaba 8UAPS?

    Found on p48, works alright.

    Andy
  23. Replies
    9
    Views
    857

    I have contacted Immersion re repair. Can you...

    I have contacted Immersion re repair. Can you recommend a more suitable power filter? How can i test the camera? Thanks Andy
  24. Replies
    9
    Views
    857

    No chance of it touching, it had a piece of tape...

    No chance of it touching, it had a piece of tape covering it and the plug was suspended from the goggles.
  25. Replies
    9
    Views
    857

    I got it from Wireless Hobby w the 600mW Tx and...

    I got it from Wireless Hobby w the 600mW Tx and Blubeams as upgrades. Sorry for crappy photo from my phone. I will try and get a closeup on the melted wire with a real camera.

    Andy
Results 1 to 25 of 26
Page 1 of 2 1 2