image

Search:

Type: Posts; User: Yosemite; Keyword(s):

Page 1 of 16 1 2 3 4

Search: Search took 0.04 seconds.

  1. hopefully they see this i finally bought the...

    hopefully they see this
    i finally bought the fill size tx and hooked it up with a external battery and going to 1 watt it now stays at mode 2 most of the flight
  2. rfmd 1 and 2

    hi tbs, was using fw 2.88 and was noticing that after going a mile or so the rfmd would go to 1 and stay there until i came back in and landed. i downgraded to 2.41 and it goes to rfmd 1 a mile out...
  3. one thing i noticed with the new 2.88 fw is that...

    one thing i noticed with the new 2.88 fw is that the rfmd is 2 until i go out a mile or so then it goes to 1 and it will stay there and not go back to 2 even though i am only a few hundred feet away,...
  4. TBS- updated to 2.88 and no more "sensor lost"...

    TBS- updated to 2.88 and no more "sensor lost" !!!
    78931
  5. Replies
    639
    Views
    216,582

    Sticky: same frames, x220,, crossfire mini with stock...

    same frames, x220,, crossfire mini with stock antenna, latest stable firmware 2.41 or 2?, the one with the brainfpv radix keeps going "sensor lost" although all values look good, the bardwell f4...
  6. Replies
    639
    Views
    216,582

    Sticky: i sure hope so, it is driving me crazy even when...

    i sure hope so, it is driving me crazy even when all readouts are good
  7. Replies
    639
    Views
    216,582

    Sticky: thanks good to know, now if i could just get rid...

    thanks good to know, now if i could just get rid of the "sensor lost" call out on my taranis!
  8. brainfpv radix, crossfire, v2.4, i am constantly...

    brainfpv radix, crossfire, v2.4, i am constantly getting the "sensor lost" although it seems like rssi, rqly, and rfmd are good after going out 1.5 mile, and fix for this? never got this before on 3...
  9. Replies
    639
    Views
    216,582

    Sticky: after crossfire 2.4 update the TPWR(mw) shows as...

    after crossfire 2.4 update the TPWR(mw) shows as 0 in the taranis logs when set to 250mw, it used to show the power changes
  10. Replies
    2
    Views
    595

    thanks for the great explanation! i will push a...

    thanks for the great explanation! i will push a little farther to the batteries limits!
  11. Replies
    2
    Views
    595

    crossfire micro telemetry chart analysis

    can some one interpret this chart from a x220 quad and micro? horizontal antenna placement
    it seems ok as rfmd never went to 0 and rfmd was never below 70%. is TPWR the power the TX is putting out?...
  12. Replies
    4
    Views
    703

    been going 1.6 mile easy on a micro on a x220,...

    been going 1.6 mile easy on a micro on a x220, great signal and video, only limiting factor is battery, 1300mh, with a 1500mh i could go farther
  13. X220 - TBS Crossfire Micro - 2K Flight - Logs, how do they look?

    these are from a 2k flight with stock antenna in dipole configuration on lower plate, rear.
    was wondering if any folks with experience in reading these could comment?

    thanks

    RFmd
    77893
    ...
  14. Thread: EZUHF Nano RX

    by Yosemite
    Replies
    283
    Views
    55,796

    after reading all this about the ezuhf sbus i...

    after reading all this about the ezuhf sbus i went with the tbs crossfire. have been using the ezuhf for 5 years now with great success on ppm but with lack of support of sbus as it is in "beta" i...
  15. thanks fyathyrio, it is wired to the crossfire...

    thanks fyathyrio, it is wired to the crossfire micro as shown, and there is no option for non-inverted in cf menu. channel 1 from the cf is to ppm/sbus uart6 enabled, channel 2 from cf is to ch4/rx6...
  16. thanks, this one here, wired as shown in photo,...

    thanks, this one here, wired as shown in photo, rssi, everything works
    http://www.readytoflyquads.com/flip-32-f4-omnibus-v3
    77800
  17. omnibus f4sd and crossfire, wiring suggestions?

    tried tx/rx3 and tx/rx6 and no luck. put tx on sbus uart6, ch2 onto rx6 and it all seems to work

    i have seen suggestions to try tx/rx3 and tx/rx6 never had any luck

    anyone have any experience...
  18. solved, used omnibus instead of cheap banggood board

    solved, used omnibus instead of cheap banggood board
    ------------------------------------------------------------

    first time setup with the cf micro bundle and i am getting no output on receiver...
  19. Replies
    8
    Views
    1,170

    have used your products for years with great...

    have used your products for years with great success. this is a new one and there were no directions on how to configure it in irctools, did not want to try the 4 channel lite or any other rx for...
  20. Replies
    8
    Views
    1,170

    they did get back to me by email shortly after my...

    they did get back to me by email shortly after my posts and said they would get a manual and update irctools to support the nano, but since then i have not heard a word, they said use the 4 channel...
  21. thank you for the reply! it does seem to work...

    thank you for the reply! it does seem to work selecting the 4 channel, changed to muxed and it is now talking to bf.

    but to have to search and search for this info instead of it being in a manual...
  22. Replies
    8
    Views
    1,170

    anybody home? need help with nanorx

    maybe i am blind but i can not find a manual for the nanorx

    at this nano page, there is fw but the manual is just the generic immersion one, no nano in it. i had no clue how to attach the antenna...
  23. Thread: EZUHF Nano RX

    by Yosemite
    Replies
    283
    Views
    55,796

    Where can one find the latest irc tools that...

    Where can one find the latest irc tools that support s the nano and where is the manual? The manual at the immersion site on the nano page has nothing in it about the nano
  24. Where to download IRCTools with support for nanorx?

    can any one point me to where you can download the latest IRCTools with support for nanorx?

    i have 1.42.5 so not sure if it is the latest as i can not find any download area on the immersion site...
  25. Replies
    3
    Views
    886

    thanks so much for getting back. yes it is weird,...

    thanks so much for getting back. yes it is weird, the feiyu 3d gimbal is very nicely built and worked perfect right out of the box. BUT feiyu has non existent tech support and the software for the...
Results 1 to 25 of 387
Page 1 of 16 1 2 3 4