image

Search:

Type: Posts; User: dogear; Keyword(s):

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    145

    Set the board to D8 instead of D16.

    Set the board to D8 instead of D16.
  2. Replies
    2
    Views
    145

    Tango Battery Low Alert

    When flying a whoop with a Betafpv F4 1s Brushless Flight controller (Frsky + OSD) after around 30-45 seconds of flight the Tango starts beeping briefly the display on the screen shows Battery Low....
  3. Thread: TBS POWERCUBE

    by dogear
    Replies
    1,751
    Views
    358,339

    Thanks very much

    Thanks very much
  4. Thread: TBS POWERCUBE

    by dogear
    Replies
    1,751
    Views
    358,339

    TBS POWERCUBE V2 (4IN1 20A ESC)

    How do you mount this stack in the quad? Seems backwards in that the battery pads and antenna pigtail are situated facing the front of the quad instead of facing the rear of the quad. What am I...
  5. Replies
    4
    Views
    1,198

    I installed a Fat Shark Race Cam V3 and didn't...

    I installed a Fat Shark Race Cam V3 and didn't like the video so I installed a V2 and all is great now. Issue seems solved. Thanks
  6. Replies
    4
    Views
    1,198

    Smacked the quad into a roof flashing quads fine...

    Smacked the quad into a roof flashing quads fine cams toast. Thanks
  7. Replies
    4
    Views
    1,198

    Replacement Camera Mojo 230?

    Can I use an ImmersionRC Race Cam? Does it matter whether its a V2 or V3? Thanks
  8. Thanks

    Thanks
  9. Whats the difference between the international...

    Whats the difference between the international version and the us version?
  10. Replies
    4
    Views
    694

    Bad FC board worked good once I changed it out....

    Bad FC board worked good once I changed it out. Thanks
  11. Replies
    4
    Views
    694

    Yup did that and got a com error please try...

    Yup did that and got a com error please try reflash FC
  12. Replies
    4
    Views
    694

    Ummagawd Vortex 250 and OSD 1.0.0.43

    Upgraded an Ummagawd 250 Pro to OSD ver 1.0.0.43 and BF 3.17 and have lost stick control. OSD ver 1.0.0.41 works fine. Thanks
  13. Replies
    256
    Views
    68,242

    Betaflight Rates Changed After Setting Up FpVision OSD

    Has anyone noticed that the the rates are different after setting up the OSD on the FpVision board? I have tried flashing the Colibri board with Betaflight and doing no setup until after I set up the...
  14. If I flash an Ummagawd Vortex with 1.0.0.38 and...

    If I flash an Ummagawd Vortex with 1.0.0.38 and bf 3.1.5 will it lose the Ummagawd Pro tunes? Am assuming that the Pro Tunes are initiated from the OSD? Thanks
  15. Replies
    256
    Views
    68,242

    I've done a couple builds with the elite bundle...

    I've done a couple builds with the elite bundle and it takes me forever to get the soldering correct on the signal holes on the pdb and fcb so that all 4 motors spin. Seems like playing wack a mole,...
  16. Replies
    750
    Views
    156,585

    Can u tell me how u set the model up on the Tango...

    Can u tell me how u set the model up on the Tango to work with Freerider? Also I can't get the iMac to respond to the Tango at all. Assuming you start the Tango up in USB mode by holding the scan...
  17. Replies
    13
    Views
    1,420

    You can go here...

    You can go here http://www.immersionrc.com/fpv-products/vortex-250-pro/ bottom of page to "Downloads" and get the Ummagawd firmware for both the Fusion board and the OSD. They are bundled. Use...
  18. Replies
    13
    Views
    1,420

    Thanks for your help.

    Thanks for your help.
  19. Replies
    13
    Views
    1,420

    I flashed both the OSD and FC. More info on this...

    I flashed both the OSD and FC. More info on this issue: this quad crashed in the snow and moisture subsequently encroached inside. I changed the Fusion board, flashed both OSD and FW and the quad now...
  20. Replies
    13
    Views
    1,420

    I read that post about the Ummagawd version 11...

    I read that post about the Ummagawd version 11 but it was not me who wrote it. I flashed the version that you can currently download from ImmersionRC's site for the standard Vortex and it has that...
  21. Replies
    13
    Views
    1,420

    Flashed with the download from Immersion RC. Quad...

    Flashed with the download from Immersion RC. Quad has solid red light no boot up LED sequence and all the reset button does on the LED board does is change the colors of the LEDs. Otherwise the quad...
  22. Replies
    13
    Views
    1,420

    Thx for the info cheers

    Thx for the info cheers
  23. Replies
    13
    Views
    1,420

    Replacement Fusion Gen 2 FCB

    First question, do the replacement fcb's come pre flashed or do they need to be flashed? Also if the answer to the first question is "yes" are there different boards available for the different...
Results 1 to 23 of 23