image

Search:

Type: Posts; User: Ironfrog37; Keyword(s):

Search: Search took 0.03 seconds.

  1. I had a feeling you were going to say that. The...

    I had a feeling you were going to say that. The newer firmware allows us to have 6 channels now but I’m still using version 2.24 and it’s been working great on the 15 RX’s I have been using on my...
  2. 7903979040

    7903979040
  3. Yeah it only needs 4 channels. Rite now it is set...

    Yeah it only needs 4 channels. Rite now it is set using chn1-chn1. Chn2-chn2 and so on. I couldn’t get the zohd stabilization board to recognize sbus or ppm signal.
  4. So if I could get the zohd dart to run on sbus on...

    So if I could get the zohd dart to run on sbus on channel 1 and use crsfTX on channel 3 and crsfRX on channel 4 and wire the TX and RX wire to the evo TX and RX ports I should get LQ and RSSI ?
  5. TBS Unify EVO With Crossfire RX using BST

    Hi I was wondering if was possible to use the BST connection on the crossfire micro RX or Nano RX (SCL,SDA) to send your RSSI and LQ to the OSD on the EVO? I have a crossfire micro RX in my ZOHD...
  6. Replies
    256
    Views
    72,358

    Thanks Steve for all the help everything is...

    Thanks Steve for all the help everything is working as it should and I am getting the same RSSI readings in my OSD that you posted.
  7. Replies
    256
    Views
    72,358

    No I have not powered it up yet. Wanted to ask if...

    No I have not powered it up yet. Wanted to ask if I should put chn12 back to chn12 instead of LQ or RSSI in the tbs nano RX? And turn off RSSI in betaflight under receiver tab?
  8. Replies
    256
    Views
    72,358

    Here is the picture didn't load last time. 78463

    Here is the picture didn't load last time.
    78463
  9. Replies
    256
    Views
    72,358

    Hi Steve Thanks for the help. I wired up my nano...

    Hi Steve Thanks for the help. I wired up my nano RX to my Oblivian using the UART1 port on top of the flight controller. Ground to ground 5volt to 5 volt chn1TX to UART1RX and chn2RX to UART1TX. I...
  10. Replies
    256
    Views
    72,358

    Should I just connect a wire from the BST SDA and...

    Should I just connect a wire from the BST SDA and BST SCL of the Nano to the bottom board of the power cube BST SDA and BST SCL pins? I can’t really find the pin layout for the FPVision OSD board...
  11. Replies
    256
    Views
    72,358

    Hi all. I got an Oblivian which has Powercube and...

    Hi all. I got an Oblivian which has Powercube and FPVision installed and I have the Crossfire Nano for my RX. I was wondering if there was a way to get RSSI thru the OSD using the Nano? I have tried...
  12. Replies
    5
    Views
    2,427

    I just got my TBS Oblivian few days ago and got...

    I just got my TBS Oblivian few days ago and got it setup with the crossfire nano RX and the Spektrum iX12 using the Crossfire TX. Also added a beeper to it. Got flight modes, arming switch and beeper...
  13. Replies
    4,880
    Views
    1,015,175

    Hi all. Well I don’t know what was wrong with the...

    Hi all. Well I don’t know what was wrong with the micro RX I was trying to use but it no longer powers up and I think it is dead. So I plugged another new RX in and set it up as stated above and...
  14. Replies
    4,880
    Views
    1,015,175

    Hi my micro RX V2 is freezing up and only showing...

    Hi my micro RX V2 is freezing up and only showing channel 4 on my crossfire TX then starts a rapid flash green light on the micro RX when switching channel 1 to CRSF TX. When this happens there is...
  15. Replies
    4,880
    Views
    1,015,175

    Hi I have a few question on using the TBS...

    Hi I have a few question on using the TBS crossfire micro receiver V2. I am planning on using it in a wing with servo plugs for two servos and and ESC to motor. Could you use the TBS servo adapter...
  16. Replies
    2
    Views
    453

    Hi from Pennsylvania!

    Hi all! I have been in the RC hobby since 2009 using cars, planes, and drones. I have had my HAM radio licence for almost two years and have been getting into the FPV flying of drones and planes....
Results 1 to 16 of 17