image

Search:

Type: Posts; User: Moose_Roberts; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.04 seconds.

  1. Replies
    5
    Views
    2,283

    I have somewhat of a similar issue. I have two...

    I have somewhat of a similar issue. I have two builds, almost the same setup, Betaflight F3 flight controllers, both running Unify Pro V2's, one is adjustable through the LUA and the OSD controls,...
  2. Replies
    67
    Views
    16,335

    That video came out right in time.

    That video came out right in time.
  3. Replies
    67
    Views
    16,335

    Not confusing, it makes sense. I'm wondering why...

    Not confusing, it makes sense. I'm wondering why Alex recommends the Mad Mushroom, with that in mind though. Is it about axial ratio or radiation pattern over raw power output?
  4. Replies
    67
    Views
    16,335

    Circularization shouldn't matter on the Tx...

    Circularization shouldn't matter on the Tx antenna for this, correct? The signal is going to a linear antenna on the Rx, so if one happened to have a 2.4 airblade then it should do as well as a mad...
  5. Replies
    697
    Views
    158,485

    Sticky: Question: If I print a cover for the reflector on...

    Question: If I print a cover for the reflector on my square goggle mount helical, is that going to have an adverse effect on reception? The v3 has a cone of sorts on there, was jut wondering if thin...
  6. Your results make it look like more of an...

    Your results make it look like more of an underpowered 400mW on the high power setting. I wonder how the 600mW version measures on the high end. Thanks for the review.
  7. Replies
    29
    Views
    9,843

    Quite the mystery, my friend. I had issues with...

    Quite the mystery, my friend. I had issues with my Rev5 Naze, which is closer to the mini, but no issues with the Rev6 by doing the described. Maybe poke it with a stick, or try bribing it?
  8. Replies
    29
    Views
    9,843

    I'm not running resistors with no issues. I'm...

    I'm not running resistors with no issues. I'm assuming you have the Smartport lead from your XSR split, or have the two pins jumped somehow. If that is the case then I would leave the Baud on auto...
  9. Replies
    19
    Views
    1,464

    Great point. I work on paintball guns and often...

    Great point. I work on paintball guns and often lecture folks on wasting money on aluminum parts to replace plastic parts. Eventually the aluminum stuff wrecks what the plastic parts were protecting.
  10. Replies
    11
    Views
    1,612

    jones007, did you cut the top and bottom plates?...

    jones007, did you cut the top and bottom plates? I'm working on getting a nice 3D printer and a CNC router table for my classroom and this would be an awesome project. If you are willing to share...
  11. Wait, yeah, it was on here, you were in that...

    Wait, yeah, it was on here, you were in that thread... See, slept since then.
  12. Leave the rate on auto, it works fine. I have...

    Leave the rate on auto, it works fine. I have seen where some people put a resister in the jumper setup they built for the 5 and 6 pin, but I didn't and have had no issues. I have the same setup and...
  13. Replies
    19
    Views
    1,464

    I prefer to land via a very elaborate cartwheel,...

    I prefer to land via a very elaborate cartwheel, so if I don't break props on every battery I snap one off for consistency. However, left my prop bucket at home the other day and was given a set of...
  14. Replies
    29
    Views
    9,843

    I got mine working with no resistors. Did the...

    I got mine working with no resistors. Did the jumped lead for 5 and 6 (softserial1) and was having issues getting telemetry pushing through to my Taranis. I double checked that I had did the CLI...
  15. Replies
    29
    Views
    9,843

    Was the telemetry just not working for you...

    Was the telemetry just not working for you through the smartport connection? What were you getting exactly before the I'm having issues as well, and I have it simply jumped to both softserial pins...
  16. Replies
    29
    Views
    9,843

    I just got an XSR when I ordered my Taranis. Very...

    I just got an XSR when I ordered my Taranis. Very small, like Ede said, the form factor is marginally smaller than a X4R or D4R naked, so preference really. However, the wiring runs pretty clean...
  17. Replies
    8
    Views
    1,890

    I am pretty sure you are right about that group....

  18. Replies
    65
    Views
    6,361

    Yesterday someone called my cell phone from a...

    Yesterday someone called my cell phone from a yet-to-be disclosed government agency asking that I register as a wearer of boxer-briefs. Registration was 3 dollars and they wanted very little personal...
  19. Replies
    328
    Views
    129,379

    Sticky: Do I take this as the reason the 285 plate is on...

    Do I take this as the reason the 285 plate is on super clearance and should buy one while they are available?
  20. Replies
    8
    Views
    1,890

    Do you guys know if that group still meets at the...

  21. Replies
    328
    Views
    129,379

    Sticky: Do you guys plan on doing a Vortex 250 bottom...

    Do you guys plan on doing a Vortex 250 bottom plate like you do for the 285?
  22. Replies
    11
    Views
    1,606

    I live in horse country in Florida, that app...

    I live in horse country in Florida, that app lists every straight piece of dirt road as an "airport" around here. I guess any horse farmer that has ever even thought about taking off in one of those...
  23. Replies
    8
    Views
    1,890

    Is there somewhere locally that like minded...

  24. As a former employee of the federal government,...

    As a former employee of the federal government, and a current employee of the local government, I support this opinion fully.

    DS, I agree, and I really think these regulations are a way to bring...
  25. Thanks, I looked it over. Hover seems to do what...

    Thanks, I looked it over. Hover seems to do what it is supposed to, provides relevant info and a little extra. B4UFLY looks like it lists every straight stretch of dirt road long enough tot land a...
Results 1 to 25 of 38
Page 1 of 2 1 2