image

Search:

Type: Posts; User: lucky72; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    6
    Views
    311

    I own a room full of planes but my top three are...

    I own a room full of planes but my top three are the Opterra, RMRC Recruit, and a Penguin. My goto plane is always the Penguin. DragonLink control with dipole antenna, 1.3 video with ET OSD. 3S...
  2. Hi, I have owned and flown DL over 6 years on...

    Hi,
    I have owned and flown DL over 6 years on currently 6 aircraft with zero drama. There is a bit of a learning curve with binding and installation etc. But it all can be worked out. I did find...
  3. Replies
    3
    Views
    394

    The short answer is one is a whip(long) and the...

    The short answer is one is a whip(long) and the other a rubber duck. Frequency typically drives the length of the antenna. If Im not mistaken the inside of the rubber duck is more than a simple wire,...
  4. Replies
    4
    Views
    1,060

    I for one don't fly over people or houses, cars,...

    I for one don't fly over people or houses, cars, boats etc...I don't consider it safe.
    Stephen
  5. Thread: Rssi question.

    by lucky72
    Replies
    7
    Views
    538

    Yes it was taken from Hobby Kings website

    Yes it was taken from Hobby Kings website
  6. Thread: Rssi question.

    by lucky72
    Replies
    7
    Views
    538

    I googled Multistar Razor 40A Tower F4 , and...

    I googled Multistar Razor 40A Tower F4 , and checked the manual at the site, its under downloads. I assume it is the unit you have? Left side middle of the board labeled RSSI. Some receivers are set...
  7. Thread: Rssi question.

    by lucky72
    Replies
    7
    Views
    538

    RSSI pin is labeled AD2 on the manual, also you...

    RSSI pin is labeled AD2 on the manual, also you may have to enable it during the the OSD programming.
  8. Replies
    6
    Views
    598

    Remember to post what you find out, it may help...

    Remember to post what you find out, it may help someone with a similar problem
  9. Replies
    6
    Views
    598

    I apologize for not being much help. But here are...

    I apologize for not being much help. But here are my thoughts, If it was me I would go to the vTx board and check the connector or solder pads, they are almost always labeled(Gnd/5-12V/Video/Sound....
  10. Replies
    6
    Views
    598

    Pics would help as well as the vTx brand/model.

    Pics would help as well as the vTx brand/model.
  11. Replies
    2,116
    Views
    743,709

    Good Job Brett~!

    Good Job Brett~!
  12. Replies
    2
    Views
    218

    Maybe you can modify the fan equipped faceplate...

    Maybe you can modify the fan equipped faceplate to work with your base??
  13. Still fly my Penguin...rock solid and stable. The...

    Still fly my Penguin...rock solid and stable. The mini quad thing didnt hold my appeal, prefer slow easy cruising around. Just finished a Eflite Opterra and loving it too..
  14. Agreed! Gonna fly this weekend without...Flying...

    Agreed! Gonna fly this weekend without...Flying the wing isnt an issue, I was hoping it would assist on the launch, this thing is farking big! Will work thru it till the Eagletree gets here. I find...
  15. Thanks Beer for your help...gonna order an...

    Thanks Beer for your help...gonna order an Eagletree and setup like my Penguin. I know that will work:cool: We have already invested to much time on an 18 dollar piece of electronics, will use it for...
  16. This is a DLV2, worked with it a bit this morning...

    This is a DLV2, worked with it a bit this morning with no luck...I have a new V3 receiver, guess I will pull it from the plane and see if it will work with it for shits and giggles.
  17. I have verified stand alone both units worked as...

    I have verified stand alone both units worked as designed. PWM vs PPM output may have something to do, if the DL Rx outputs are PPM vs PWM that maybe the problem. I believe the 2.4 Rx are normally...
  18. The wiring is male to male from Rx to Orange and...

    The wiring is male to male from Rx to Orange and servos plugged into Orange as you would normally to a Rx. Swapping out the DL Rx with a FrSky 2.4 and it works as it should
  19. Yes/ I have verified the DL works when servos are...

    Yes/ I have verified the DL works when servos are hook directly to DL and 2.4/ but when the Orange is place between the DL I have no control but the stabilization works. When placed between the 2.4 I...
  20. Dragonlink wont play nice with Hobby King stabilizer?

    I use the little Hobby King Orange stabilizers in smaller planes. Cheap and effective. I recently tried using one with my DragonLink receiver...nope nada nothing? Works perfect with FrSky 2.4 but no...
  21. Replies
    31
    Views
    4,084

    You may find this helpful as well:) Make sure you...

    You may find this helpful as well:) Make sure you stay with in the weight limits of the design...it's easy to get a fat plane really fast!
    https://<iframe width="560" height="315"...
  22. Replies
    31
    Views
    4,084

    Check out this site, it may help with what Im...

    Check out this site, it may help with what Im talking about.

    http://hobby-on-rc.blogspot.com/2012/10/cutting-aileronson-wing-when-building.html
  23. Replies
    31
    Views
    4,084

    Nathaniel LOL Mona Lisa, nope, but I do my...

    Nathaniel
    LOL Mona Lisa, nope, but I do my best..thank you. I built another back in 1992 with a OS .15 and it flew well, slow and took for ever to land. The wing servo are mounted on a flat plate on...
  24. Replies
    31
    Views
    4,084

    1..wings were a pain/thin balsa snapped easily...

    1..wings were a pain/thin balsa snapped easily
    2..adding the ailerons, took a lot of figuring, adding strength for hinges and drilling servo wire hole in all the ribs
    3..the wood parts quality is...
  25. Replies
    31
    Views
    4,084

    The project looks fantastic! Like you I have had...

    The project looks fantastic! Like you I have had to work around this and that. The DynaFlite kit is horrible and has to be fidgeted a lot with, not to mention the modifications added by me. I use a...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4