image

Search:

Type: Posts; User: lucky72; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    10
    Views
    7,979

    Hi Tom, not sure what the problem could be? The...

    Hi Tom, not sure what the problem could be? The forums are visible to me. Hope you get it sorted out.
  2. Replies
    2
    Views
    6,391

    Hobby King sells one for 40 bucks. Works thru the...

    Hobby King sells one for 40 bucks. Works thru the trainer port of your transmitter. The website has the manual PDF available for you to read.Quanum 3 Axis No Drift Head TrackerMy 2 cents, I used the...
  3. Replies
    6
    Views
    1,611

    I own a room full of planes but my top three are...

    I own a room full of planes but my top three are the Opterra, RMRC Recruit, and a Penguin. My goto plane is always the Penguin. DragonLink control with dipole antenna, 1.3 video with ET OSD. 3S...
  4. Hi, I have owned and flown DL over 6 years on...

    Hi,
    I have owned and flown DL over 6 years on currently 6 aircraft with zero drama. There is a bit of a learning curve with binding and installation etc. But it all can be worked out. I did find...
  5. Replies
    3
    Views
    1,315

    The short answer is one is a whip(long) and the...

    The short answer is one is a whip(long) and the other a rubber duck. Frequency typically drives the length of the antenna. If Im not mistaken the inside of the rubber duck is more than a simple wire,...
  6. Replies
    5
    Views
    7,076

    I for one don't fly over people or houses, cars,...

    I for one don't fly over people or houses, cars, boats etc...I don't consider it safe.
    Stephen
  7. Thread: Rssi question.

    by lucky72
    Replies
    7
    Views
    2,074

    Yes it was taken from Hobby Kings website

    Yes it was taken from Hobby Kings website
  8. Thread: Rssi question.

    by lucky72
    Replies
    7
    Views
    2,074

    I googled Multistar Razor 40A Tower F4 , and...

    I googled Multistar Razor 40A Tower F4 , and checked the manual at the site, its under downloads. I assume it is the unit you have? Left side middle of the board labeled RSSI. Some receivers are set...
  9. Thread: Rssi question.

    by lucky72
    Replies
    7
    Views
    2,074

    RSSI pin is labeled AD2 on the manual, also you...

    RSSI pin is labeled AD2 on the manual, also you may have to enable it during the the OSD programming.
  10. Replies
    6
    Views
    2,097

    Remember to post what you find out, it may help...

    Remember to post what you find out, it may help someone with a similar problem
  11. Replies
    6
    Views
    2,097

    I apologize for not being much help. But here are...

    I apologize for not being much help. But here are my thoughts, If it was me I would go to the vTx board and check the connector or solder pads, they are almost always labeled(Gnd/5-12V/Video/Sound....
  12. Replies
    6
    Views
    2,097

    Pics would help as well as the vTx brand/model.

    Pics would help as well as the vTx brand/model.
  13. Replies
    2,118
    Views
    809,189

    Good Job Brett~!

    Good Job Brett~!
  14. Replies
    2
    Views
    739

    Maybe you can modify the fan equipped faceplate...

    Maybe you can modify the fan equipped faceplate to work with your base??
  15. Agreed! Gonna fly this weekend without...Flying...

    Agreed! Gonna fly this weekend without...Flying the wing isnt an issue, I was hoping it would assist on the launch, this thing is farking big! Will work thru it till the Eagletree gets here. I find...
  16. Thanks Beer for your help...gonna order an...

    Thanks Beer for your help...gonna order an Eagletree and setup like my Penguin. I know that will work:cool: We have already invested to much time on an 18 dollar piece of electronics, will use it for...
  17. This is a DLV2, worked with it a bit this morning...

    This is a DLV2, worked with it a bit this morning with no luck...I have a new V3 receiver, guess I will pull it from the plane and see if it will work with it for shits and giggles.
  18. I have verified stand alone both units worked as...

    I have verified stand alone both units worked as designed. PWM vs PPM output may have something to do, if the DL Rx outputs are PPM vs PWM that maybe the problem. I believe the 2.4 Rx are normally...
  19. The wiring is male to male from Rx to Orange and...

    The wiring is male to male from Rx to Orange and servos plugged into Orange as you would normally to a Rx. Swapping out the DL Rx with a FrSky 2.4 and it works as it should
  20. Yes/ I have verified the DL works when servos are...

    Yes/ I have verified the DL works when servos are hook directly to DL and 2.4/ but when the Orange is place between the DL I have no control but the stabilization works. When placed between the 2.4 I...
  21. Dragonlink wont play nice with Hobby King stabilizer?

    I use the little Hobby King Orange stabilizers in smaller planes. Cheap and effective. I recently tried using one with my DragonLink receiver...nope nada nothing? Works perfect with FrSky 2.4 but no...
  22. Replies
    7
    Views
    1,104

    [QUOTE=matmo26;805773]Ok I get that, I should...

    [QUOTE=matmo26;805773]Ok I get that, I should have said thru s.bus instead of to s.bus.. question is how to make the switch function with the vectors mode settings..

    This is the way mine is set up...
  23. Replies
    2
    Views
    844

    In hindsight I should have tested everything...

    In hindsight I should have tested everything individually first, the motors I tested on a known good ESC later, one was DOA and the other would spin up and after a few seconds lock up. My biggest...
  24. Replies
    2
    Views
    844

    Unplanned water landing

    I failed to heed the Tarot FC battery warning and didn't quite make it back to land:(. The place is Glendale SC. My daughter wanted to take some scenic pics for a school project and I decided to pull...
  25. Thread: Attitude V2

    by lucky72
    Replies
    2
    Views
    703

    Jeff can you post a picture of the damage please....

    Jeff can you post a picture of the damage please. May be helpful for others to see and respond.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4