image

Search:

Type: Posts; User: Mark97564; Keyword(s):

Page 1 of 18 1 2 3 4

Search: Search took 0.05 seconds.

  1. The newest firmware version does work fine... I...

    The newest firmware version does work fine... I litterly had to ramp up the throttle to draw 6 to 8 amps for almost 10 seconds and then it changed to max output
  2. Replies
    160
    Views
    30,325

    Use mission planner, and the settings been the...

    Use mission planner, and the settings been the same for years... the Sr settings are more towards the bottom
  3. Replies
    1
    Views
    844

    I'm thinking because you connect battery voltage...

    I'm thinking because you connect battery voltage to the camera and smart audio from a osd or flight controller and then you connect the tbs unify vtx to the output wires... And the camera feeds...
  4. Replies
    8
    Views
    739

    Yes, I finally got it resolved... I flashed the...

    Yes, I finally got it resolved... I flashed the vortex firmware beginning with the very first version I have saved from downloading it back in 2015 and slowly installed newer versions until the...
  5. And since this thread has sassens attention, I'm...

    And since this thread has sassens attention, I'm hoping he can tell me how to get the runcam uart to osd adapter to work on my vortex 250 and the pin out of the fun connector along with the 2...
  6. Just so everyone who reads this thread knows I...

    Just so everyone who reads this thread knows I finally got it working like it should... I flashed the very first version of vortex osd and beta flight firmware along with 3 newer ones and finally...
  7. Sticky: Also this pin out for the stm32f1 which I'm...

    Also this pin out for the stm32f1 which I'm pretty sure is a pin for pin replacement of the f3? The terminals in question are labeled Swdio which is pin 34 and swdclk which is pin 37, those go to one...
  8. Sticky: Does anyone know what the 2 connectors are for on...

    Does anyone know what the 2 connectors are for on the fusion 2 flight control board? 'I know the 1 is uart 3 for sbus, or serial receivers, but what about the other 2? 2 pins of each are power but...
  9. Replies
    8
    Views
    739

    Did you get it figured out? I'm kinda having the...

    Did you get it figured out? I'm kinda having the same issue with a vortex 250 after installing the tramp vortex module.. The only way I can get more power output than 24mw is by using the tramp...
  10. This guy seems to be having the same issue as I...

    This guy seems to be having the same issue as I am...

    http://fpvlab.com/forums/showthread.php?52990-Video-power-low-out-of-the-box
  11. So do you agree with me now? That the osd...

    So do you agree with me now? That the osd firmware has a bug in it? There is no other explanation for why it isn't working when setting the tramps power output with the vortex osd
  12. I put my original 350mw vortex vtx module back...

    I put my original 350mw vortex vtx module back into my vortex and on low I get 110mw of output, high I get 380mw of output and when I set it to auto I get 380mw with it armed and disarmed.. So...
  13. It is the blade version of the vortex 250, and it...

    It is the blade version of the vortex 250, and it is advertised as having a 350mw vtx and when I click on the link for the manual it says it's the international version.. When I look under the...
  14. Besides, if it was limited to 25mw, then why is...

    Besides, if it was limited to 25mw, then why is it only getting set for 24mw? The tramp app and my power meter are showing 24mw
  15. How can I tell? It says us next to the osd...

    How can I tell? It says us next to the osd version number.. and if it is locked how can I get it unlocked? Can you send me a different firmware version? Or sell me a new part? Every vtx I've ever...
  16. I just tested again, low on the osd setting is 1...

    I just tested again, low on the osd setting is 1 mw no matter what, and 25,200,350, and max settings are all 12 mw with the vortex disarmed and 24mw armed ... So it is automatically switching the...
  17. I've tried it armed and with props on......

    I've tried it armed and with props on... according to the tramp configurator app it's only set at 24mw.. and when I change the power output with the app it changes instantly and puts out the power...
  18. I've got the newest version of osd firmware and...

    I've got the newest version of osd firmware and beta flight installed, it lets you think it's changing the settings but if you check with a power meter or the tramp configurator app for android you...
  19. Who gets the email at repairs@immersionrc.com? I...

    Who gets the email at repairs@immersionrc.com? I don't understand what they can do for me that immersion rc support on the forum can't.... All I need is updated osd firmware that has the tramp...
  20. Replies
    7
    Views
    1,270

    Mine is the internation version, and if I use the...

    Mine is the internation version, and if I use the Android tramp config app I'm able to set the power output just fine.. and with getting static when I switch between the odd and config app I'm pretty...
  21. I have about 4 or 5 days ago and have not heard...

    I have about 4 or 5 days ago and have not heard from them yet... I'm 99% sure the issue is the firmware on the vortex 250 osd though...
  22. Replies
    10
    Views
    2,032

    It should work, I know it does on the vortex 250...

    It should work, I know it does on the vortex 250 and 285 with the fusion 2 flight controller.... Osd displays speed and heading though, not coordinates if I remember correctly, but the coordinates...
  23. Replies
    7
    Views
    1,270

    I am having the same issue.. Download the vortex...

    I am having the same issue.. Download the vortex configurator app from the google play store with a phone or tablet that has nfc built in and you can then scan the tramps nfc tag and read it. It...
  24. Google playstore, but you Need a phone or tablet...

    Google playstore, but you Need a phone or tablet with nfc, if the device isn't compatable the app won't show up... but if you do, just open Google play store and type tramp config In the search bar...
  25. Could someone at immersion rc let me know if they...

    Could someone at immersion rc let me know if they seen my posts or not please? It would be nice to know so I know a fix is in progress or not, ya know....

    thank you
Results 1 to 25 of 434
Page 1 of 18 1 2 3 4