image

Search:

Type: Posts; User: Guda; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.13 seconds.

  1. I didn't have 5v going to the Naze32. Once I...

    I didn't have 5v going to the Naze32. Once I hooked up a BEC the servo started to do the same thing. So I stripped the FPV system out of it & as of now it's my 1st failure. I'll come back to it in...
  2. Anyone else annoyed that chrome has to open to use cleanflight?

    Google chrome is a RAM pig. I never use it. But for some reason the cleanflight guys like it. I just want to use what I want to use. I don't want to have to run a pig of a browser to use cleanflight....
  3. Update, switched from 1.10 to 1.9 & used this...

    Update, switched from 1.10 to 1.9 & used this code in CL " servo 5 1100 1900 1500 101 -1 " & then " save " Servo has stopped spinning, tying to fine some crazy un achievable home (good thing). As...
  4. I just finished the 2nd one of these I have &...

    I just finished the 2nd one of these I have & it's making the same "chirping" sound. Happens when landing & throttling all the way down. How would it work to set it so 0 throttle comes sooner?
  5. Funny thing it I thought you worked for them.......

    Funny thing it I thought you worked for them.... GIVE THIS GUY A FREE SOMETHING GETFPV!!!



    An attitude that you should be known whats up, but production levels to supply 100x more components...
  6. I have always used 3. 1 feels different, less...

    I have always used 3. 1 feels different, less forgiving. That worked though for the flight issues. But the chirping still happens when I land sometimes. It's good there is a solution & someone to...
  7. Hi, having the same problem. Then I found this...

    Hi, having the same problem. Then I found this post & the problem is maybe 10% better after changing all the settings just like in the photos above.

    I built a QAV250 with the old ESC a month or...
  8. Replies
    88
    Views
    8,481

    Shouldn't the feds figure out how to stop mass...

    Shouldn't the feds figure out how to stop mass shooting before worrying about drones? The feds are really scared of drones because they have the potential to be the great equalizer. I for 1 am not...
  9. Replies
    249
    Views
    52,707

    RT/TX

    RT/TX
  10. Replies
    1
    Views
    520

    I should have just done this. As one of these...

    I should have just done this. As one of these lame compression nut shafts just came off during flight smashing the frame. :(
  11. Different lengths of wires to different ESC is a...

    Different lengths of wires to different ESC is a issue no? IE tale ESC 4x further away from PDB/FC than ones on arms.

    When I hooked it up. I had to put some throttle to it. The motor was barely...
  12. Replies
    249
    Views
    52,707

    Some cameras don't work with OSDoge.

    Some cameras don't work with OSDoge.
  13. Replies
    1
    Views
    520

    JB weld compression prop adapter?

    I have these 3m shafts with a compression sleeve to attach a 5m threaded shaft over. 2 get tight enough 2 don't. Any thing wrong with JB welding them on?
  14. I started asking this because I'm building a...

    I started asking this because I'm building a Harrier & I'm using KISS ESC & I can put them wherever I like as they have no wires. I have seen them soldered directly to a PDB & that looked pretty...
  15. I did just have a ESC fry & I didn't know why. I...

    I did just have a ESC fry & I didn't know why. I connected the ESC & motor wires at the ends of both as I needed the length. I tested it & it worked fine with a servo tester but POOF when connected...
  16. Long motor wires or Long power, ground & signal wires?

    Is it better to have long motor wires or long power ground & signal? I can either mount the ESC next to the motor or next to the PDB. Which is better?
  17. Talking to cleanflight Twitter, So I am warning...

    Talking to cleanflight Twitter, So I am warning anyone who is going to buy a tricopter, DONT!. Cleanflight is messed up & DOES NOT SUPPORT tricopter. Unfortunately this probably won't reach anyone...
  18. Thread: Issue with OSDoge

    by Guda
    Replies
    8
    Views
    1,436

    Wow, this was my solution also. Out out 3 cameras...

    Wow, this was my solution also. Out out 3 cameras the one on the OSDoge didn't display the OSD. Then I fried one because it was 5v & I had the board set to 12v for the other camera. But before it...
  19. Okay. Super bummer. Does this mean all tricopters...

    Okay. Super bummer. Does this mean all tricopters are grounded ? Whats this "parse error" I get when trying to put the code in CLI?
  20. I don't have another one. The one I have tested...

    I don't have another one. The one I have tested fine. I just tested it again with a servo tester & it works fine. I'm not savvy enough to know what "pot resistance" is but I know the servo works fine...
  21. I don't have another. I tested the one that came...

    I don't have another. I tested the one that came with the frame & it worked fine with a servo tester. Now the servo turns 1/2 turn clockwise & then back counterclockwise about 1 turn then stops...
  22. Anyone know how to make cleanflight tricopter...

    Anyone know how to make cleanflight tricopter servo tab save?
  23. Update. I disassembled the tail, now the servo &...

    Update. I disassembled the tail, now the servo & the tilt are separate. The servo keeps making noise after its turned all the way counter clockwise. Like its trying to turn past its limit. I'm sure...
  24. Tricopter tail servo keeps spinning when plugged in

    Hello, I've searched around & tried everything?

    Problem, tall servo keeps spinning clockwise when plugged in. I unplug quickly as to not burn out the servo.

    I've tried resetting the values in...
  25. Thread: Frsky UHF

    by Guda
    Replies
    2
    Views
    633

    Frsky UHF

    Howdy, how much trouble is it to switch back & forth between the Frsky standard 2.4 & a UHF mod on the Taranis ?
Results 1 to 25 of 46
Page 1 of 2 1 2