image

Search:

Type: Posts; User: rgfidler; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.06 seconds.

  1. Set up manual does not do a good job in...

    Set up manual does not do a good job in explaining how each parameter effects flight characteristics. I kind of gave up playing with the settings because did not notice much difference. What iwas...
  2. Replies
    16
    Views
    10,161

    Just a follow up to my problems. Eagle Tree has...

    Just a follow up to my problems. Eagle Tree has answered every question without delay. and I am satisfied with my Vector. I think they are a good company, with good people and good products. I will...
  3. What is center stick mode?

    What is center stick mode?
  4. Replies
    2
    Views
    911

    I did lower the stab Responsiveness from 3 to 2...

    I did lower the stab Responsiveness from 3 to 2 and that did help some. The gps position hold does not work with the setting I have which have been adjusted per your instructions in manual. No...
  5. Replies
    2
    Views
    911

    Vector Gain & Response adjustment

    I have been trying to adjust gain control on a Quad I am using for a Vector testbed.


    Gain controls do not seem to have any effect on changing how the quad reacts to radio controls inputs. The...
  6. Replies
    3
    Views
    13,889

    Sticky: Yes, your are what you say Mark, keep up the...

    Yes, your are what you say Mark, keep up the great job. I am using my Hornet as a Eagle Tree Vector controller test bed. That would be a good video for you guys to do.
  7. Thread: Unarm Vector

    by rgfidler
    Replies
    7
    Views
    1,250

    Select fast arming, please provide a little...

    Select fast arming, please provide a little direction of how to find in the men,
  8. Thread: Unarm Vector

    by rgfidler
    Replies
    7
    Views
    1,250

    [QUOTE=JohnET;531838]Hello, Actually, the left...

    [QUOTE=JohnET;531838]Hello,

    Actually, the left stick down and right is the arm command, not unarm command. The behavior you see is correct. If you hold the left stick to the bottom right, you will...
  9. Thread: Unarm Vector

    by rgfidler
    Replies
    7
    Views
    1,250

    Unarm Vector

    After setting up Vector and doing motor test, when I unarm by rudder stick down and right, all 4 props spin about 1 turn, but no turn when throttle is applied. No faults on OSD, so no clue on what...
  10. Replies
    16
    Views
    10,161

    Quad setup that worked with a Naza V2, Vector OSD...

    Quad setup that worked with a Naza V2, Vector OSD menu does not respond to stick input from tx, so dead in the water. DX8 Spektrum tx and ar8000 rx
  11. Glad you have your Vector working. My Vector will...

    Glad you have your Vector working. My Vector will not setup as of today, and have requested help to see how eagletree responds to my request for help. Your rig seems to fly quite well.
  12. Replies
    16
    Views
    10,161

    Eagle Tree Vector Problems

    2 days of setup and still no worky. Anyone out there having problems with the Vector?
    I asked for help for Eagletree, will report back about my progress.
  13. Replies
    249
    Views
    26,533

    I believe it lost gps signal and drifted off by...

    I believe it lost
    gps signal and drifted off by the wind because it flew behind me over the house and by the time I got my goggles off it was gone.
  14. Replies
    249
    Views
    26,533

    Good news , ship found today almost intact,within...

    Good news , ship found today almost intact,within 500 ft, few busted parts but cost to fix should be minimal, all major parts including gopro intact.
    Today was my lucky day.
  15. Replies
    249
    Views
    26,533

    I had a 1.3 300m/w vtx New Custom ReadymadeRC us...

    I had a 1.3 300m/w vtx New Custom ReadymadeRC us version with a 1.3 IBCRAZY Blue Beam Antenna
  16. Replies
    249
    Views
    26,533

    No chance in manual, had a full green lock before...

    No chance in manual, had a full green lock before takeoff, but the previous flight I had lost full full green lock and it had started to wander. Puck from VTX about 3 inches and yes video 1.3.
  17. Replies
    249
    Views
    26,533

    Not sure I understand your point Hans. I am not...

    Not sure I understand your point Hans. I am not interested in a debate about anything or geting envolved in a debate about the quality of any vendors equipment. My post is to inform other FPV'ers of...
  18. Replies
    249
    Views
    26,533

    Naza V2 Fly Away

    Happened to me yesterday in Florida. I was flying my new QAV400 with a Naza V2/GPS,
    with FPV goggles yesterday. I had just taken off without goggles and flying about 10 ft of altitude and say 30 ft...
  19. Replies
    2
    Views
    1,975

    Thanks for info STI-REX. I have also learned that...

    Thanks for info STI-REX. I have also learned that increasing throttle throw to 120% high and low before you calibrate esc, then return radio to 100% after calibration. This will get the motors to...
  20. [QUOTE=timnilson;220683]Yes, you will need to...

    [QUOTE=timnilson;220683]Yes, you will need to calibrate the throttle -- this is to teach the ESCs what your TX/RX has for its max and min values. You power up your ESC with the TX on and in max...
  21. Replies
    2
    Views
    1,975

    Luminier ESC calibration to transmitter

    Anyone out there understand exactly how to calibrate lumenier 30a motor esc on a QAV400. I have seen videos of quads that fly unstable because the esc's have not been calibrated to the transmitter....
  22. Replies
    1
    Views
    733

    EZuhf Rx 4 channel

    Looking for info on rx LED, I get a rapid flashing of the LED light when I turn on the TX,
    what does this mean?
  23. Thread: CC3D

    by rgfidler
    Replies
    14
    Views
    5,461

    Usb may not be providing the ccd3 with enough...

    Usb may not be providing the ccd3 with enough amperage. Suggest you use a powered USB connection.
  24. Help Setting Up TBS Pro | Michigan preferred

    I have a used TBS Pro (looks like new) that I am trying to setup with a Naza V2 controller, EZuhf tx and rx using a Taranis radio. The goal would be to send the complete package to a individual with...
  25. Replies
    41
    Views
    17,282

    Thank you for your very detailed response. After...

    Thank you for your very detailed response. After reading, some questions have come up.


    The battery for the taranis and the EZuhf needs to be updated to a 12 volt with the new connector as you...
Results 1 to 25 of 42
Page 1 of 2 1 2