image

Search:

Type: Posts; User: hydev; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    0
    Views
    136

    Connector name JST-something!

    Hi,

    What is the name of the connector into the TBS 2.4 ghz 500mw or Unify VTX? I know itís JST something but which variety?

    Thanks

    Mike


    Sent from my iPad using Tapatalk
  2. The 1.3ghz stiff wonít dip down to the crossfire...

    The 1.3ghz stiff wonít dip down to the crossfire range... your vtx outputs (say) 1280 and sticks to it, otherwise you would lose the video feed.

    You might use a low pass filter if your using...
  3. Is 2.4Ghz FPV a good choice with Crossfire for trees and proximity to structures

    Heís just asking about using 2.4ghz for video and the quality of it. Heís using crossfire so there wonít be any issues in that area. I have a similar question but with 1.3ghz.

    Mike


    Sent...
  4. Thread: TBS VENDETTA

    by hydev
    Replies
    1,536
    Views
    364,475

    If your in the UK the New HobbyRC.co.uk is...

    If your in the UK the New HobbyRC.co.uk is normally good. However I use 6x4 tri blades, very smooth.

    Mike
  5. Hi mate, I can confirm doesnít work if using...

    Hi mate, I can confirm doesnít work if using windows 7 or 10 as a VM must be a native machine for it to work. I had the same issue a few months back. If using a Mac then install a Bootcamp...
  6. Replies
    5
    Views
    1,506

    maybe save money and pick some batteries up from...

    maybe save money and pick some batteries up from elsewhere? Antenna included are ok


    Sent from my iPad using Tapatalk
  7. Replies
    5
    Views
    1,506

    Looks good but bigger battery, 2200mah size. ...

    Looks good but bigger battery, 2200mah size.


    Sent from my iPhone using Tapatalk
  8. Replies
    4,866
    Views
    970,501

    Can I ask what people use for telemetry on...

    Can I ask what people use for telemetry on Taranis X9D/OpenTx 2.2? I want the TX to read out the signal strength to me, whats best to use, RQly or TQly?
  9. Thread: FlashError 6

    by hydev
    Replies
    1
    Views
    424

    Fixed it. I was using a VM and when I tried it...

    Fixed it. I was using a VM and when I tried it on full blown normal natural PC it worked fine.

    Mike
  10. Thread: FlashError 6

    by hydev
    Replies
    1
    Views
    424

    FlashError 6

    Hi,

    I am trying to update my TBS CORE PRO PNP PRO. However, when I plug it in, it doesn't' get recognised. I then hold Enter down and it goes it Emergency mode. The TBS Agent then immediately...
  11. You have a common ground for the VTX and Camera? ...

    You have a common ground for the VTX and Camera? Does it change if you power up the motors?
  12. Replies
    81
    Views
    32,379

    I have exactly the same problem, ticket raised,...

    I have exactly the same problem, ticket raised, 726322.

    Mike


    Sent from my iPad using Tapatalk
  13. Thread: C clips

    by hydev
    Replies
    0
    Views
    551

    C clips

    Where can I get replacement c-clips for my TBS Mr Steele motors? Or does anyone know the size? I'm based in the U.K.

    Thanks

    Mike
  14. Replies
    2
    Views
    1,016

    When you check Cleanflight/Betaflight is the...

    When you check Cleanflight/Betaflight is the flight controller definitely seeing the receiver? Go to that tab and check.
  15. Replies
    4
    Views
    682

    Ok, so if mess it up, then it doesn't actually...

    Ok, so if mess it up, then it doesn't actually need any resistors as it's 0 ohm. :-)
  16. Replies
    4
    Views
    682

    Changing voltage on TBS CORE Pro

    I have a TBS Core PRO and I want to change the VTX voltage from 5V to 12V. I understand from manual I need to solder across the pads rom 5v to 12v. However, in the manual it looks like a direct...
  17. Replies
    263
    Views
    84,919

    Can I clarify you have a separate partition on...

    Can I clarify you have a separate partition on your hard disk and are using boot camp? If that is the case then disregard my advice. I thought you were using a Windows10 virtual machine within OSX....
  18. Replies
    263
    Views
    84,919

    Are you using Parallels? Have you installed the...

    Are you using Parallels?
    Have you installed the Mac drivers on the Macbook Air AND the Windows drivers in your Win10 instance?
    If so is the device recognised in your Windows10 parallels? i.e. Go...
  19. Replies
    263
    Views
    84,919

    Hi, I have just flashed to Betaflight 2.9.1...

    Hi,

    I have just flashed to Betaflight 2.9.1 Vendetta using the TBS Agent and when I arm the motors they spin very fast. I put the props on and held the quad down and tried it - in my view that...
  20. Thread: TBS VENDETTA

    by hydev
    Replies
    1,536
    Views
    364,475

    TBS VENDETTA

    I'm thinking of installing this on my Vendetta, does it fit easily?


    Sent from my iPhone using Tapatalk
  21. Replies
    1,057
    Views
    149,613

    Did you ever get a response to this? I have just...

    Did you ever get a response to this? I have just brought this VTX and would like to get the frequency correct.


    Mike
  22. Replies
    3
    Views
    743

    Right, thank you, I see what you mean. Makes...

    Right, thank you, I see what you mean. Makes sense 😀
  23. Replies
    3
    Views
    743

    Right, thank you, I see what you mean. Makes...

    Right, thank you, I see what you mean. Makes sense ��
  24. Replies
    3
    Views
    743

    Cleanflight and LED's

    I have just got some programmable LED to use with my Naze32 board and Cleanflight. I'm running the latest stable firmware but I'm clearly missing something with the LED programming..

    (I...
  25. "Your MinimOSD KV Board is fine - that is exactly...

    "Your MinimOSD KV Board is fine - that is exactly what i use. What you need to do is connect the Battery Voltage wires to the MinimOSD BATT2 & BATT2 GND connections, not BATT1."

    "With your voltage...
Results 1 to 25 of 31
Page 1 of 2 1 2