image

Search:

Type: Posts; User: MrScott; Keyword(s):

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    1,089

    Cool, thanks a bunch

    Cool, thanks a bunch
  2. Replies
    5
    Views
    1,089

    Trinity and pan/tilt/roll: Pan question

    I've got the trinity module working with the FS pan/tilt/roll mount and a second pan and tilt unit. Both are working great but it would be better if I could pan up to about 270 degrees. Is there a...
  3. Thread: Video tx cable

    by MrScott
    Replies
    0
    Views
    429

    Video tx cable

    I bought a 1.3 and a 5.8 250mW transmitters to replace rmrc video tx. I took the cable and attached a Jr style plug for the power, video and ground. I took a Futaba style plug for the sound and...
  4. Replies
    2
    Views
    1,150

    Very good, thanks!

    Very good, thanks!
  5. Replies
    2
    Views
    1,150

    Clover leaf antenna orientation

    I ordered my rmrc 1.3 package and came with a bluebeam clover leaf antenna. Ive seen all types of these antennas mounted with the lead at the bottom and the clover leaf on top. My question is, does...
  6. Replies
    9
    Views
    1,184

    That got it. Both are at 1.53 and I have 12...

    That got it. Both are at 1.53 and I have 12 channels availabe


    I would have had it months ago, but the firmware update was a bit challenging

    Thanks,
    Scott
  7. Replies
    9
    Views
    1,184

    Still trying to figure this thing out... i...

    Still trying to figure this thing out...

    i picked up a Taranius 9x and set it up to output 12 channels. Worked great, the IRC tool kit sees 12 channels. But the RX only sees 8. 9-12 still grayed...
  8. Replies
    4
    Views
    1,291

    Very good, thank you

    Very good, thank you
  9. Replies
    9
    Views
    1,184

    It says: Version: 1.50 (6) For both the TX and RX

    It says: Version: 1.50 (6) For both the TX and RX
  10. Replies
    159
    Views
    77,707

    Sticky: Im stuck with 8 channels and I need a couple...

    Im stuck with 8 channels and I need a couple more. Here is what I have:

    JR8103 8 ch TX
    Ezuhf JR module
    Diversity 8ch RX
    FatShark Dominators with Trinity H/T
    ET Vector
    E-Flite Apprentice
    ...
  11. Replies
    9
    Views
    1,184

    What is "pwm 12"? I see PPM all over the place...

    What is "pwm 12"? I see PPM all over the place but nothing on pwm.

    Still trying to make it work, thanks
  12. Replies
    4
    Views
    1,291

    Surprise!! i was able to make the rssi and LQ...

    Surprise!!

    i was able to make the rssi and LQ work properly on channel 6 and 8. Now all I need to do is to figure out why the signal goes from great to not great at random times.

    And, since...
  13. Replies
    9
    Views
    1,184

    Can't do that, ppm 9 thru 12 are grayed out. You...

    Can't do that, ppm 9 thru 12 are grayed out. You mean the servo maping tab right? The configure tab only lets me change the diversity and the frequency band

    on the bright side, I got RSSI and lq...
  14. Replies
    4
    Views
    1,291

    EZUHF RSSI and Vector

    In the channel maping section of the IRC and Vector software, I set channel 8 for RSSI. On the Vector software it show that the RSSI data is being properly received and displayed on my monitor, but...
  15. Replies
    9
    Views
    1,184

    Why can I only see 8 channels

    I'm trying to set up RSSI between my 8 channel diversity receiver and my Vector. Everything I read says the RSSI needs to be on channel 12, but on the servo mapping tab of the toolbox 1.42.5,...
  16. Replies
    0
    Views
    1,279

    Vector rssi from ezuhf diversity receiver

    I've been flying with the Vector for a few months and doing well. I ordered the ezuhf diversity receiver and JR 433mhz module. I got it to work after about 2 hours and a lot of cussing. But the rssi...
Results 1 to 16 of 16