image

Search:

Type: Posts; User: Sbatty; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.14 seconds.

  1. Replies
    11
    Views
    2,113

    Thankfully, I learn that I am not the only person...

    Thankfully, I learn that I am not the only person with this exact question. I too am running 4s with 600mw VTX and a 12v camera. I currently am using a Polou step-up, but it is negatively effecting...
  2. Replies
    21
    Views
    7,116

    Hell, I bought this quad knowing that this had...

    Hell, I bought this quad knowing that this had happened. Just had my maiden with it a few minutes ago. Hopefully, I will someday taco it is a similar fashion.
  3. Replies
    20
    Views
    4,348

    McCleary, you missed the 4s 4200mah lipos -- buy...

    McCleary, you missed the 4s 4200mah lipos -- buy two get one free. I am sure Tim is cool with it. :cool:
  4. Replies
    7
    Views
    3,755

    Skinnydoc, I am a practicing attorney and...

    Skinnydoc,

    I am a practicing attorney and member of our local school board and am looking to share some ideas with our teachers. Like you I am interested in finding a curriculum that can bring...
  5. Alright, stupid question time. I just received...

    Alright, stupid question time. I just received my camera and was about to install it in the case. Having never wored with a CCD board camera before I realized that I had no idea how to remove the...
  6. Just received my shipment this afternoon from...

    Just received my shipment this afternoon from RMRC.

    I went with an 8" RMRC Monitor
    IRC Uno and VTX
    VAS Bluebeam Ultra antenna set.

    Also got the monitor mount from Polakium Engineering. Now I...
  7. FPV Baby Steps - Setup Critique and Antenna Questions

    I have been reading threads here and there for months and I am finally ready to take my first step into FPV. Now, I am finding myself over-analyzing every single decision and hesitating before I...
  8. Replies
    7
    Views
    2,587

    Not at all. Just that you need to notify any...

    Not at all. Just that you need to notify any airport within 5 miles of your backyard and hope that they don't say no.
  9. Replies
    7
    Views
    2,587

    Fighting stupid with stupid

    Last night I was zipping around the neighborhood with a 250 size mini quad thinking about the recent FAA notice. Now my quad weighs a little over a pound, I was flying LOS, and never even exceeded a...
  10. Replies
    0
    Views
    468

    Salvage Ops: 2.4Ghz Receiver

    I have been learning on a mini quad where space is at a real premium. Flying on a TH9x with a FlySky 6channel receiver. Because of space concerns the case has been stripped off and the receiver...
  11. Replies
    0
    Views
    1,047

    Ambarella A9 SOC hints to Hero 4 Specs

    Ambarella released some information on the A9 SOC recently.

    http://www.ambarella.jp/uploads/docs/A9-product-brief.pdf

    Considering that the GoPro 3+ Black uses the A7 SOC while the White and...
  12. Thanks Derrick, at least I know the pitch now. ...

    Thanks Derrick, at least I know the pitch now.

    Can anyone confirm that the eclip on the bottom of the motor is a 1.5mm?
  13. Replies
    6
    Views
    1,835

    Alright, now I am stumped. I ran the motor...

    Alright, now I am stumped.

    I ran the motor under load yesterday. After about a 90 seconds the motor slowed dramatically, I cut throttle and thermaled the ESC and motor and temps were no bad. I...
  14. Replies
    6
    Views
    1,835

    Just got done playing with the thermal. ESC...

    Just got done playing with the thermal.

    ESC on power-up:
    http://i.imgur.com/KRdqSJE.jpg
    I was actually surprised to see that on power-up it jumped to 96 degrees almost instantly.
    ...
  15. Replies
    6
    Views
    1,835

    So IR checked out fine. Bearings appeared to be...

    So IR checked out fine. Bearings appeared to be in good shape. The only physical damage I found was a slight flattening of the housing that may have caused the magnets to be closer to the stator...
  16. Thread: Mini quads

    by Sbatty
    Replies
    57
    Views
    13,597

    I have read posts regarding problems with the RCX...

    I have read posts regarding problems with the RCX 1804s but I have personally had no problems.
  17. Thread: Mini quads

    by Sbatty
    Replies
    57
    Views
    13,597

    Recently built up a mini on a 250mm 3D printed...

    Recently built up a mini on a 250mm 3D printed framehttp://polakiumengineering.org/?product=super-simple-mini-h-quad-v3-sshquad-fpv

    Running RCX-1804s, with cheap plastic 5030 props and an Acro...
  18. Replies
    595
    Views
    24,037

    Poll: This flat lander is stuck in an area with no FPV...

    This flat lander is stuck in an area with no FPV fliers. I may have to come down to see how its done.
  19. An actual locknut or just the cone shaped prop...

    An actual locknut or just the cone shaped prop nut?
  20. Replies
    6
    Views
    1,835

    Last time I worked on anything RC related was...

    Last time I worked on anything RC related was about 20 years ago. I forgot how far those things fly.
  21. Replies
    6
    Views
    1,835

    Diagnosing Post-Crash Problem (RCX 1804)

    So despite the durability problems I have seen posted online I took a gamble on the 1804's and have been pleasantly surprised. Multiple severe crashes (some onto concrete) have not budged the...
  22. Interested in this as well. RCX claims that the...

    Interested in this as well. RCX claims that the threading will not work with a metric locknut. It would be great if a US vendor could find and sell a compatible locknut with nylon insert. Twice I...
  23. Replies
    6
    Views
    676

    Thanks everyone. I just need to find the...

    Thanks everyone. I just need to find the appropriate forum area for stupid noob questions when parts arrive next week.
  24. Replies
    7
    Views
    772

    Right now I am looking for stock fiberglass or...

    Right now I am looking for stock fiberglass or carbon fiber sheets that I can cut down to make accessory plates. I plan on doing a case in the summer but I need some supplies right now. Anyone have...
  25. Thread: The Techpod!!!

    by Sbatty
    Replies
    1,927
    Views
    319,629

    Sticky: Let me start off with a full disclaimer. I am a...

    Let me start off with a full disclaimer. I am a complete noob getting into this hobby as a photographer with some RC background so I tend to focus on camera issues as I am learning.

    That said,...
Results 1 to 25 of 39
Page 1 of 2 1 2