image

Search:

Type: Posts; User: fahrvergnuugen; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.03 seconds.

  1. Dip switches on 700mw 2.4ghz USA version vtx

    The manual for the 2.4 GHz video transmitter says that there are different channels for the international version versus the USA version.

    The problem is that there is only one DIP switch diagram...
  2. I think you are in the right place. What's your...

    I think you are in the right place. What's your question?
  3. The GUI confused me. You canít change which UART...

    The GUI confused me. You canít change which UART itís using without checking the box, but you canít connect with the box checked if the FC board is already in pass through mode.
  4. Thoughts on making a crossfire to sbus protocol...

    Thoughts on making a crossfire to sbus protocol converter instead of having to use the bst port?

    i guess it would be bad if the Arduino crashed because you would lose your control link, but I...
  5. That was it. THANK YOU!! That's 5 hours of my...

    That was it. THANK YOU!!

    That's 5 hours of my life I won't ever get back :rolleyes:
  6. I cannot get serialpassthrough to work with iNav!...

    I cannot get serialpassthrough to work with iNav!

    I have a PiggyOSD connected to an RMRC Dodo on UART2 @ 115200 baud rate.
    RX,TX & GND are hooked up and valid data is being displayed on the OSD....
  7. Yes, thatís the exact response I got.

    Yes, thatís the exact response I got.
  8. Ticket sent. Not holding my breath though, the...

    Ticket sent. Not holding my breath though, the Vector is getting quite long in the tooth. It wouldn't surprise me if they are putting all their effort into something new.

    EDIT: They replied and...
  9. By the way, I'm also from Upstate NY (1 hour...

    By the way, I'm also from Upstate NY (1 hour north of Albany) - what city are you near?
  10. It's funny you mentioned that because I was also...

    It's funny you mentioned that because I was also thinking of trying to make an arduino based converter. It's a shame ET won't add native crossfire support.

    Anyway I'm definitely interested if you...
  11. Eagle Tree Vector Open Telemetry protocol with Crossfire?

    There are a few really old threads (2+ years) about this but I haven't seen any recent updates or news.

    The Vector flight controller has a UART port which can be configured to output "Open...
  12. Pitot sensor reads 180mph when stationary

    I can't figure out why my vector OSD is displaying ~180mph on the OSD. I configured it to show the air speed from the pitot sensor. When I disable the pitot in the configuration the speed reads 0mph...
  13. 8ch Diversity RX LED rapidly flashing when powered on

    The red led on my 8ch diversity RX rapidly flashes as soon as power is given to the RX, either by USB or by the BEC. My vector can't detect any channels from the RX.

    Is it dead?
  14. Anyone else have this problem? (Unify Pro 5v)

    Delete
  15. Replies
    81
    Views
    32,381

    Hey Trappy, This might be difficult to answer...

    Hey Trappy,
    This might be difficult to answer but - will I kill my Unify Pro if I remove the heatshrink to silicone conformal coat it and then re-heatshrink? I ask because the conformal coating +...
  16. Hey Trappy, I was thinking about ordering a Unify...

    Hey Trappy, I was thinking about ordering a Unify HV to replace my ancient (and huge) 600mw IRC VTX.

    Would I have this video line issue with Kiss 24A ESCs?
  17. Replies
    13
    Views
    1,306

    Hi Ron, i am definitely going to test with 3s...

    Hi Ron,
    i am definitely going to test with 3s and I'm sure my range will improve, but I still suspect something else is wrong.

    Fwiw, I had a different ezuhf external tx powered by the same...
  18. Replies
    13
    Views
    1,306

    Hi Ssassen, If it were a power issue wouldn't...

    Hi Ssassen,
    If it were a power issue wouldn't the RSSI value be low?
  19. Replies
    13
    Views
    1,306

    Just to sanity check - what dbm is an acceptable...

    Just to sanity check - what dbm is an acceptable noise floor?
  20. Replies
    13
    Views
    1,306

    Thats a good question, I will have to try that....

    Thats a good question, I will have to try that. Will do further testing tomorrow.
  21. Replies
    13
    Views
    1,306

    I wonder where I could be getting noise from. I...

    I wonder where I could be getting noise from. I ran the spectrum analyzer on the bench and the plane doesn't seem to be emitting anything that would cause interference.

    I'm flying in a really...
  22. Replies
    13
    Views
    1,306

    100% RSSI with 1% Link?

    I have an EzUHF transmitter (standalone module) with Diamond antenna and an 8 channel diversity RX with stock antennas. The RX is mounted on top of my plane with the dipole antennas pointing up in a...
  23. I just spent hours battling this issue -...

    I just spent hours battling this issue - compounded by the fact that the bind button on my RX is broken so I had to short the pins with tweezers.

    I think the problem is that once you bind the RX &...
  24. Sticky: I really really really wish you made a 6" version...

    I really really really wish you made a 6" version of this. We use these for slow flying through the woods (totally different experience then racing or acro). The heavier frame would benefit immensely...
  25. Replies
    4
    Views
    715

    Is the 470 coil bottom right in the picture? If...

    Is the 470 coil bottom right in the picture? If so it's just the way the photo came out, doesn't look like that by eye.
    do you what the resister is that i melted? It would be worth the 10 cents to...
Results 1 to 25 of 33
Page 1 of 2 1 2