image

Search:

Type: Posts; User: IceWind; Keyword(s):

Page 1 of 15 1 2 3 4

Search: Search took 0.14 seconds.

  1. Replies
    4
    Views
    759

    I noticed this as well as I started using the...

    I noticed this as well as I started using the Goggles vRX module.
    I can clearly seen the signal bars raising as soon as I power the EzUHF.

    Tried different channels (on the 5.8 video), tried to...
  2. Replies
    1
    Views
    716

    bump... Any answer to this. New FC, new OSD ,...

    bump...

    Any answer to this.
    New FC, new OSD , same issue...
    77906
  3. Thank you. In the new one as well, I think I...

    Thank you.
    In the new one as well, I think I save my last change... just need to know where I put it. :)
  4. Hey, I was searching for this but couldn't fine...

    Hey, I was searching for this but couldn't fine mention to it. (probably didn't used the proper search terms)

    Is it normal for the GUI not to be able to load the current screen layout?
    If I make...
  5. Replies
    9
    Views
    2,473

    Mine ended up having the driver board replaced.

    Mine ended up having the driver board replaced.
  6. @someitdude In the end until we get a fix for...

    @someitdude

    In the end until we get a fix for the 8chn RX, i'm using the 4chn RX.
  7. Sure I'll do that. Btw, I don' think this is...

    Sure I'll do that.
    Btw, I don' think this is hardware related but rather software/firmware related as I can replicate in other rx's of teh same model.

    Cheers.
  8. EzUHF 8chLite // Can't get min signal lower than 1009us

    Hi,

    When trying to setup my EzUHF 8chLite rx (FW: 1.53) to use with iNAV I face the following issue.
    The minimal signal it sends per channel is 1009, I'm using a taranis radio (Fw: Opentx 2.2.0)...
  9. Replies
    1
    Views
    716

    Dominator HD2 cropped image

    Hey,

    I don't use much OSD's or similar stuff so I hadn't noticed this before.
    I was adding a call-sign in my CCD (HS1177) for easier video identification and noticed that my HD2 are cropping...
  10. Oh yes, when I'm flying with one of the lads here...

    Oh yes, when I'm flying with one of the lads here I can't open my car doors while he is using his LRS TX.
  11. Replies
    213
    Views
    42,573

    @Alex, how "rigid" are those specs? Could the...

    @Alex, how "rigid" are those specs?
    Could the wing be a "blunt nose" type ass long it as the same specs, 36'' wing span and so on?

    Personally I prefer the "blunt nose" as they provide a nice area...
  12. Replies
    9
    Views
    2,473

    Thanks Patrick. Much appreciated.

    Thanks Patrick.
    Much appreciated.
  13. Replies
    9
    Views
    2,473

    Oh gee...was about to post about the exact same...

    Oh gee...was about to post about the exact same issue.
    Have them for a few months and all good, now after power them on the image starts to get darker and darker.

    Today it went way bad...after a...
  14. Replies
    170
    Views
    25,810

    I have my battery not for long and today one of...

    I have my battery not for long and today one of the side panel fell off and I can't put it back on as the it doesn't fit back no matter how much I press it down.
    So I'm assuming the cells have...
  15. Replies
    59
    Views
    9,899

    Any chance a option to be added to the DVR to...

    Any chance a option to be added to the DVR to have increase bitrate in videos?
    I find the quality a bit lower than other DVR's I have. :(
  16. Replies
    474
    Views
    84,324

    Dude you did it again! Truly and artist. :)

    Dude you did it again!
    Truly and artist. :)
  17. Replies
    13
    Views
    6,813

    I like the color and the fan cover...

    I like the color and the fan cover...
  18. Replies
    11
    Views
    9,615

    Sticky: Any changelog for the upcoming firmware? Option...

    Any changelog for the upcoming firmware?
    Option to choose bitrate would be great, the current one is a bit too low and quality of the video isn't that great.
  19. Replies
    474
    Views
    84,324

    Surprised that all that work with the fret saw...

    Surprised that all that work with the fret saw didn't left you with a strong grip and you need those fancy tools. :)
  20. I'll be honest that I haven't looked much into...

    I'll be honest that I haven't looked much into the MWOSD code so I assumed the distance to home was calculated by the OSD rather than from the FC.
    The FW he is using is iNav not the BL or CL, so...
  21. On another topic. This happened to a friend this...

    On another topic.
    This happened to a friend this weekend, due to probably a glitch in the radio signal the channel that controls the arm/disarm may have changed causing it to disarm
    for a split...
  22. There aren't that many sensors out there. We...

    There aren't that many sensors out there.
    We could submit them and list them in the Wiki for direct reference?
  23. Cool thanks. I had the sensor powered and...

    Cool thanks.
    I had the sensor powered and plugged to the OSD so it was receiving live data.
  24. Hey guys. I'm trying to set my voltage/current...

    Hey guys.

    I'm trying to set my voltage/current sensor Attopilot 90A but without much luck.
    I used the cal button in the UI to set the sensitive value of 36.6mv/A as in the datasheet.

    One...
  25. Why did he say that, what are is reasons?...

    Why did he say that, what are is reasons?
    Because saying just don't it is nothing. :)

    The Taranis already comes with OpenTX installed so what you'll be doing is just installing firmware updates....
Results 1 to 25 of 372
Page 1 of 15 1 2 3 4