image

Search:

Type: Posts; User: daBKLYNdoorman; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.02 seconds.

  1. Can someone provide power specs on the TBS GPS...

    Can someone provide power specs on the TBS GPS unit? Specifically, I need to know whether its 3.3v or 5v, the type of GPS chip inside, and the wiring which is what cable?
  2. +1 Use a 5.8Ghz Crosshair on both and aim at...

    +1
    Use a 5.8Ghz Crosshair on both and aim at each other. That's an additional 16db of signal strength over your rubber ducky omni's. Run at a low 25mw signal power, you don't need more for a...
  3. Replies
    324
    Views
    91,955

    You're out of luck. I'd just ask TBS to cancel...

    You're out of luck. I'd just ask TBS to cancel the exchange and ask for a refund if still possible.

    The interference will be the same on all those frequencies you mentioned... either go 2.4 for...
  4. Replies
    324
    Views
    91,955

    Same here... just sold my Crossfire and ordered a...

    Same here... just sold my Crossfire and ordered a DL V3...
  5. Replies
    324
    Views
    91,955

    Some Iftron YellowJacket vs RMRC w/saw filter...

    Some Iftron YellowJacket vs RMRC w/saw filter test results as it pertains to the Crossfire TX being nearby.

    Test setup:
    "Aircraft" side: On a long block of wood I had a 1W Iftron VTX with Mad...
  6. Replies
    324
    Views
    91,955

    I'm the somebody you are referring to. Been busy...

    I'm the somebody you are referring to. Been busy lately (bought a house) and am finishing up my wood-kit built 3m plane (Bearospace Gemini). I will perform some more tests this weekend hopefully if...
  7. Replies
    324
    Views
    91,955

    I have a YellowJacket and a Crossfire. Using a...

    I have a YellowJacket and a Crossfire.
    Using a Moxon on the Crossfire (up to 500mw) and a Mad Mushroom on the YellowJacket, I found zero (nadda, nothing) interference when holding the two antennas...
  8. Be careful with these NCR18650B's - they have a...

    Be careful with these NCR18650B's - they have a low thermal runaway threshold.
    If you measure the temperature, chances are you are measuring that of a more ventilated cell, likely towards the...
  9. My ground testing has shown almost no effect at...

    My ground testing has shown almost no effect at 10mw, 25mw, 100mw. At 500mw, I began to see a little bit of noise in the video when I held the TX a meter from the video RX.

    Using an Iftrontech...
  10. I had a similar problem (mentioned few pages back...

    I had a similar problem (mentioned few pages back in time), a replacement JR module adapter fixed the problem permanently.
    In the meantime while waiting for the replacement to arrive, I took apart...
  11. Hi guys, any updates?

    Hi guys, any updates?
  12. Do you only connect the RSSI signal wire (white),...

    Do you only connect the RSSI signal wire (white), or do you also connect the ground (black) wire to the Vector?
  13. Remove the black plastic holding the TX and...

    Remove the black plastic holding the TX and adapter and check below it, if I remember correctly, that's were my RX was located.
  14. Both no signal, just tried. Update I switched...

    Both no signal, just tried.

    Update I switched from PPM to "XJT D16" and I get finally get Signal OK.... weird.... but every few seconds it goes back to No Signal... and switched back to Signal OK
  15. Yes and yes. See attached photos...6673866736

    Yes and yes. See attached photos...6673866736
  16. Yeah, firmware CROSSFIRE v1.00 on both. Just...

    Yeah, firmware CROSSFIRE v1.00 on both. Just checked.

    I'm thinking RC Input has to do with PPM signal from Taranis... but I double checked the settings (and the pins this time :D) and all looks...
  17. Is anyone else getting "No Signal!" for RC Input...

    Is anyone else getting "No Signal!" for RC Input on the XFire TX?

    Everything else seems to work excellent, just trying to figure out this one.
  18. Ok, I may be a bit exaggerating when I say I bent...

    Ok, I may be a bit exaggerating when I say I bent the pins... more like a nudge to the right side. And yes, one has to be very careful not to "bend" the pins and risk breaking the solder joint.
    ...
  19. BINGO Cheers go to @c5galaxy and @FPVFlyer!...

    BINGO Cheers go to @c5galaxy and @FPVFlyer! Indeed, the pins on the Taranis did not go into the sockets on the XFire JR module. It is actually clearly visible if you hold the two very close together,...
  20. I'm running my Taranis off the convenient NiMh...

    I'm running my Taranis off the convenient NiMh battery that came with it. I guess I could perhaps tap into that battery to get 7.2v nominal into the XFire TX...

    But first as Perna suggested, I'll...
  21. So finally had some time to get started on the...

    So finally had some time to get started on the EZUHF to Crossfire swap... and... my Crossfire TX doesn't turn on when my Taranis turns on... :(

    Any idea what the problem might be?

    1. I have...
  22. How will power be supplied to the BST Bus? (...

    How will power be supplied to the BST Bus? (
    Since manual says Crossfire doesn't supply 5v to Bus, then I assume Vector will do it?)
  23. John, any updates? Especially interested in...

    John, any updates?

    Especially interested in the GPS info from Vector to Crossfire.

    Thanks in advance.
  24. To take advantage of find/lost/beacon plane...

    To take advantage of find/lost/beacon plane feature
  25. From manual: Huh? But later it says:

    From manual:





    Huh?

    But later it says:
Results 1 to 25 of 56
Page 1 of 3 1 2 3