image

Search:

Type: Posts; User: turbiner; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.26 seconds.

  1. Replies
    3
    Views
    1,015

    I have fitted it almost 2 inches from CG with no...

    I have fitted it almost 2 inches from CG with no problems on fixed wing
  2. It's possible that there is a setting on your TX...

    It's possible that there is a setting on your TX to control the number of channels transmitted through the trainer port but I am not familiar with the Graupner TX. Have a look at the trainer section...
  3. I don't know much about your transmitter but I...

    I don't know much about your transmitter but I assume that you are using the trainer connection to send ppm to the EZUHF TX, if so I suspect that the Graupner TX only sends a maximum of five channels...
  4. Replies
    4
    Views
    1,246

    The ESC you are using must have a BEC which is...

    The ESC you are using must have a BEC which is supplying power to the rail which in turn is connected to the servos and also through the ail/PPM cable to supply the EZUHF RX. In the video you watched...
  5. Make sure you calibrate your ESC/ESCs with the...

    Make sure you calibrate your ESC/ESCs with the throttle trim all the way up then set failsafe with the trim all the way down, there shouldn't be a problem having the trim up all the time. If you want...
  6. I know this is an old thread now but I came...

    I know this is an old thread now but I came across it while trying to set RTH with the low throttle method on Taranis/EZUHF, I wanted to free up another mode switch position and after a few hours and...
  7. Replies
    31
    Views
    3,521

    Yes that is correct - you don't need to do it but...

    Yes that is correct - you don't need to do it but it just means the trims are centered. Makes no difference to Vector.
  8. Replies
    31
    Views
    3,521

    I have never had this problem with RTH, once I...

    I have never had this problem with RTH, once I have trimmed the model I land and then incorporate trims, as above I also incorporate trims in Taranis. I have 25 hours flying time with Vector and RTH...
  9. Replies
    3
    Views
    824

    Head tracking works on any two receiver channels...

    Head tracking works on any two receiver channels which are not being used in the Vector PPM stream - completely separate from the Vector - no benefit to going through the Vector even if you could.
  10. Replies
    4
    Views
    2,248

    Hold the model at the climb angle required then...

    Hold the model at the climb angle required then switch to 3D hold and launch - works for me
  11. Replies
    159
    Views
    76,972

    Sticky: I have channels 11 and 12 mapped through the ppm...

    I have channels 11 and 12 mapped through the ppm cable as shown. The Taranis does not need any connection to channel 11 and 12. So you need EZUHF set to 12 channels but Taranis only needs to be set...
  12. Replies
    159
    Views
    76,972

    Sticky: I am using channel 11 for RSSI and channel 12 for...

    I am using channel 11 for RSSI and channel 12 for link quality and all is working well with ET Vector
  13. Replies
    0
    Views
    329

    5.8 Ghz Channel confusion

    We now have three FPV flyers at our site and need to change the default channels, we are all using the IRC 600mw VTX. The diagram in the manual shows 8 channels with the dip switch positions but the...
  14. Replies
    3
    Views
    814

    Thanks John I have opened a support ticket with...

    Thanks John I have opened a support ticket with the files attached so you can have a look at it.

    I don't use 3D, no changes to mounting or fuselage since it was all working well. I can try...
  15. Replies
    3
    Views
    814

    Vector pitching up and down in 2DH

    I have many successful hours with the Vector but on the last few flights the model (Twinstar) pitches up and down continuously in 2DH mode, the roll is fine and all is good in 2D mode. If I lower the...
  16. I am using two switches - Mode and Submode

    I am using two switches - Mode and Submode
  17. Sorry haven't got a picture but here is what I...

    Sorry haven't got a picture but here is what I did. Connect a single cable to the blue wire on the 3 Cell lipo on the ground station, tape that to your cable which goes to the goggles, cut the main...
  18. I use 2D most of the time, I also use 2DH, loiter...

    I use 2D most of the time, I also use 2DH, loiter and RTH. All work very well. Modes using Taranis.

    63527
  19. Faceplate arrived today from First Person View...

    Faceplate arrived today from First Person View here in the UK. Clips into the goggles very nicely, I found the thinner foam about right for me. I don't use the 2 cell lipo attached to the goggles so...
  20. Replies
    0
    Views
    536

    Vector OSD colours on Mobius

    Been using the Vector for sometime with no problems with various cameras but I have just connected a Mobius and the OSD colors useless, yellow comes out sort of white with flickering blue pixels and...
  21. Available for pre-order in the UK...

    Available for pre-order in the UK https://www.firstpersonview.co.uk/fpv-goggles/fatshark-dominator-video-goggles-fpv-hd-v2 but why is it black when we have nice white goggles?
  22. Replies
    3
    Views
    474

    I have the standard HT Module, not the Trinity,...

    I have the standard HT Module, not the Trinity, so I don't know if the extended range option is available in the menu.
  23. Replies
    3
    Views
    474

    Dominator V2 Headtracker - EZUHF

    Just got the head tracker up and running with EZUHF, all works well but I cannot get full right or left pan, when I move my head right or left as far as is comfortable I only get about 80 degrees. I...
  24. Your mix page looks wrong to me. I have: Mode...

    Your mix page looks wrong to me. I have:
    Mode (CH5)
    1.Not used (off)
    2.2D no hold
    3.2D + Sub Mode

    Sub Mode (CH6 shown as Mode 1 on Taranis setup)
    1.2D + Hold
    2.Loiter
    3.RTH Test
  25. I have a single switch RTH on my Taranis, are you...

    I have a single switch RTH on my Taranis, are you using Taranis?

    62267
Results 1 to 25 of 84
Page 1 of 4 1 2 3 4