image

Search:

Type: Posts; User: serpa4; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.09 seconds.

  1. Fortunately I have 3 vortex, 2x 250 and one 285....

    Fortunately I have 3 vortex, 2x 250 and one 285.
    I've never loaded anything on the quad less an update using the IRC tools. This one is brand new and never updated for flow other than a hover. It...
  2. Vortex 250 FC will not completely level out in accel calibration

    There is always a slight tilt in the quad when on a level surface when I calibrate the accelerometer.
    Any way to fix this? It's a brand new, never crashed, hovered a few minutes only. It keeps...
  3. Rotated Yaw by -90 and now it seems fine. I've...

    Rotated Yaw by -90 and now it seems fine. I've never changed it, not sure how it changed. Thanks.
  4. Replies
    9
    Views
    1,934

    It continues to be pretty high, 35-40+ sitting. ...

    It continues to be pretty high, 35-40+ sitting. However, it doesn't seem to effect the flight. I can go further than the video and peperbox allows, so perhaps a non issue.
  5. I assume your use of tow was mentioned to be...

    I assume your use of tow was mentioned to be roll. I do t know what tow is.
  6. I've tried pitch and roll. If I change by 90...

    I've tried pitch and roll. If I change by 90 degrees the animated graphic shows the quad on its side. That's because the board is already facing the right direction.
  7. Thanks, but doesn't work in that the board is...

    Thanks, but doesn't work in that the board is facing the right direction. If I change those setting, then it will show my quad tilted 90 degrees. I've tried it a few times.
  8. Pitch and roll backwards in cleanflight accelerometers!! Brand new Vortex 250.

    Still haven't flow my brand new Vortex 250, but in clean flight, the pitch and roll accelerometers are backwards! If I physically move the vortex to pitch up, the graphic shows it rolling!! And...
  9. Replies
    2
    Views
    890

    In cleanflight If I tilt the vortex to the right...

    In cleanflight If I tilt the vortex to the right to level the quad and then click the calibrate mode, it will calibrate and still calibrate with a tilt even when I have compensated it by manual...
  10. Replies
    2
    Views
    890

    Brand new Vortex 250 won't level out

    My new quad always drifts right. When attached to the computer and using cleanflight, I can select the calibrate button. It says calibrating, but the image doesn't level out. Thus, when flying it...
  11. Replies
    9
    Views
    1,934

    Both quads use the exact same receiver and...

    Both quads use the exact same receiver and antenna. Simply moving it from one quad to the other with the same battery even.
    However, 250 with bad rssi was sent to IRC for other issues. I'll see...
  12. Replies
    22
    Views
    12,085

    Just did this mod to mine. Thanks! Will save a...

    Just did this mod to mine. Thanks! Will save a lot of walking due to the receiver popping off. Neat and tidy. Fits my 2200 3s batteries very well now.
  13. Replies
    22
    Views
    12,085

    Thanks. Hows that 2.4 working for you? I will...

    Thanks. Hows that 2.4 working for you?
    I will put my RX inside my Vortex in a few days.
  14. Replies
    170
    Views
    25,815

    Mine died after 1 month! Puffed and hold 800mah....

    Mine died after 1 month! Puffed and hold 800mah. Puff, there goes my money.
    Original is 3 years old and working great!
    I've been flying and charging LIPO for years. Yes set to 2S, only 1.8A max...
  15. Replies
    1
    Views
    548

    FS 1800 mah battery warranty?

    I have a new 1800 battery for my Doms. It is about 30 days old and is puffed to expand the case and only holds ~800mah.
    Is there any warranty?
    The factory 1000mah is about 3 years old and still...
  16. Replies
    22
    Views
    12,085

    Any pictures? Thanks!

    Any pictures? Thanks!
  17. Anyone play with the altitude PID? Altitude Hold (Baro) mode.

    I'll play this next time I get to fly (4 days on at 12hr/4 days off). I don't get to fly on my work days due to no light (6am-6pm), but looking for any feedback so I know where I should start/play...
  18. Replies
    12
    Views
    2,735

    What bearing tool do you use? I found three: 1)...

    What bearing tool do you use? I found three:
    1) Muchmore Racing Brushless Motor Bearing Puller V3
    2) LRP Works Team Bearing Puller
    3) Thunder Power Z3R Bearing Replacement Tool

    No one knows...
  19. Replies
    9
    Views
    1,934

    Left is RSSI and typically all over the place. ...

    Left is RSSI and typically all over the place. What is on the right side, Link Quality?
    70900
  20. 1st flight of vortex 250 and too much jello to fly.

    Check my new vortex 250 L today for its maiden flight. The camera had so much jello that it made me nauseous. Swap the propellers it for the second set and then again for the propellers off my one...
  21. Replies
    12
    Views
    2,735

    How difficult are they to replace? I.e. special...

    How difficult are they to replace? I.e. special tools to pull them or do they slide out with a press of your finger, etc. Thanks!
    Like these I assume:...
  22. Replies
    9
    Views
    1,934

    Ok, so which way is better RSSI? I have it...

    Ok, so which way is better RSSI? I have it configured using the IRC tools on my PC.
    Is 100 the worst or best? I hope it is worst as my quad is 10-12.
  23. Replies
    9
    Views
    1,934

    They are different Vortex though! The new RED...

    They are different Vortex though! The new RED one has a LED lens over the LEDs and the 1 week old one does not. It is not a simple cover either since the reset button is integrated into the lens...
  24. Replies
    9
    Views
    1,934

    Two 250 Pro, two RX, Different RSSI???

    I have one Vortex, 1 week old, never, Never, crashed, flow for one day. Call it Vortex Green.
    I have a second one, 1 day old, never even been hovered. Call it vortex RED.
    I have two different IRC...
  25. Replies
    12
    Views
    2,735

    Motor bearing for 285?

    Mine are a bit noisy. I've sprayed and cleaned but still making noise. Are replacement bearings available so I don't need new motors?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4