PDA

View Full Version : Newbie Z3 Build Log



stevemaller
28th August 2014, 06:15 PM
This is my first wing build, so bear with me. I hope my experiences are useful to somebody, but I also wanted to provide some encouragement to folks who might not have much experience with this stuff. I had a Z2XL that I got from another guy, and I beat it up pretty badly whilst experimenting a while back. The electronics were fine, so I decided to try and build a new plane from scratch. The Z3 looked super appealing, in part because of the large internal bays. I had a struggle with the Z2 because it didn't have enough room, and I butchered it up pretty badly trying to squeeze in too much stuff.

Anyway, I jumped on this and here we go.

I'm planning to use my RVOSD 5.1 and DragonLink. I have a 2.4 and 1.3 vTX, and I'm leaning towards 1.3 because I use that on my multi rotors, too. And I have a new IBCrazy pepperbox that I think will be awesome. I have a Turnigy Dlx 70A ESC and a NTM 35-42A 1250Kv 600W motor with a 10x5 Graupner e-prop. I got Ritewing's servos as part of the kit I ordered. And I have the new Toughbay Z3H3 for my flight cam and GoPro. I think that's it, right? :-)

I dove in today, and here's where I'm at so far...

As suggested in the other build logs, I laid out the tubes and SF spars and cut them to fit. Then I taped up the wing to make sure things were aligned.

http://perspectivair.com/socialstuff/IMG_0670.jpg

After some trimming and fiddling, I went ahead and left the CF spars inside of the tubes and glued in the tubes with CA, being careful to avoid the ends of the tubes so the spars wouldn't get stuck inside! After letting things set up (with a little kicker for good measure) I went ahead and tested it. Success!


https://vimeo.com/104662783

Next moved on to trimming and gluing the little fiberglass spars on the top and bottom. Pinned them in with 'T' pins and it worked great.

http://perspectivair.com/socialstuff/IMG_0677.jpg

Now that the superstructure is in, I'm gonna have my first Gorilla Glue experience. Wish me luck!

stevemaller
28th August 2014, 08:18 PM
OK, I couldn't wait to throw a few coats of paint on this bad boy. Thanks for the paint advice, y'all!

http://perspectivair.com/socialstuff/IMG_0666.jpg
http://perspectivair.com/socialstuff/IMG_0685.jpg

represent
28th August 2014, 08:30 PM
That paint looks awesome, I know it's not done but this is the first black Z3 I've seen. Nice.

Also looks cool with the nose chopped for the Toughbox

Blizzard1287
29th August 2014, 02:57 PM
LOVING the color scheme! Seriously bad ass. Going to be watching this one :)

stevemaller
29th August 2014, 03:58 PM
LOVING the color scheme! Seriously bad ass. Going to be watching this one :)

Me, too. Fingers crossed! :-)

stevemaller
29th August 2014, 11:39 PM
Got some more work done today. I cut and monokote'd the elevons.

http://perspectivair.com/socialstuff/IMG_0687.jpg http://perspectivair.com/socialstuff/IMG_0689.jpg

The old guy at my local hobby shop gave me a great idea for cutting channels in the EPP. He sold me a $2 brass tube, and told me to cut the ends of it with my Dremel, and then use it as a hand drill. Works great!

http://perspectivair.com/socialstuff/IMG_0691.jpg

Finally, I started lam'ing the fuse and wings. Man, that's hard work! Got one wing and most of the fuse done, then I ran out of time.

http://perspectivair.com/socialstuff/IMG_0693.jpg

ritewing
30th August 2014, 11:37 AM
Looks great Steve.

stevemaller
30th August 2014, 11:59 AM
Looks great Steve.

Thanks, CK! I've been muddling along...attached one of my elevons backwards, so I had to re-do it. LMAO. I'll get there eventually.

BTW, what temp do you guys run your lamming iron at? I am using about 225F or so, and it seems to be going really, really slowly. But I'm afraid to go too high.

stevemaller
30th August 2014, 04:57 PM
Guess who my favorite band was growing up? :-)
I really have to get back to wiring this thing up.

http://perspectivair.com/socialstuff/IMG_0703.jpg

Toaster
8th September 2014, 08:00 PM
So, you're naming it the "Frankenwing", right? I'm loving this design!

stevemaller
8th September 2014, 09:53 PM
So, you're naming it the "Frankenwing", right? I'm loving this design!

You got it. I'm thinking of stenciling a big "5150" on it. :-)

Toaster
8th September 2014, 11:12 PM
I quite like that idea haha. Can't wait to see what the final product looks like! This makes me even more eager to start on mine :P

stevemaller
8th September 2014, 11:57 PM
I quite like that idea haha. Can't wait to see what the final product looks like! This makes me even more eager to start on mine :P

I'm chomping at the bit, but too busy with photoshoots to spend any more time at the moment. Next on the list is servos. I've already fired 'er up with a LiPo just to hear the motor run. I'm probably going to start with a Spektrum AR6210 and my DX8 just get her in the air. My DragonLink transmitter is in the shop (a.k.a. Mike's house) figuring out why the firmware update didn't take, so it might be another week or so before I get that back. So I just want to fly her lean and mean first (no RVOSD, either) so as not to complicate matters too much. I just want to get some time in the air with her before starting to pile in the electronics.

daggad
9th September 2014, 03:25 AM
Great tip on that tube dremeled to use as a saw !
I have found different dimensions in the house to make various channels. Plastic tube works good as well.