image
Results 1 to 5 of 5

Thread: I need HELP PLEASE! I BURNED OUT my PDB!!!

  1. #1

    I need HELP PLEASE! I BURNED OUT my PDB!!!

    I need your help guys. I have a quad with these specs and i burned out my pdb. What do you think caused this? Was wondering if the 4000 mah 10c battery has a high enough current to power this setup or do i need a batt with a higher c rating. I was wondering if I should/could switch to a 3200mah 20c or 25C. I have no idea how to find out the ampage my quad pulls and I'm really struggling with the electric side of this hobby. Any help you could give me would be much appreciated:
    OpenPilot CC3D ATOM Flight Controller (CC3D Mini Racing Edition - Bent Pin)
    DX5E Spektrum Radio
    Orange 6-Channel Rx - DSM2 and DSMX compatible 2.4Ghz receiver.
    Eachine 600tvl 1/3 Cmos FPV 110 Degree Camera w/32CH Trans
    600mW Video Transmi...tter.
    5030 Walkera props
    2x - Turnigy 4000mAh 3S 11.1v 10c discharge Lipo Battery Pack
    1- 2/3S Charger
    4x BLHeli 12amp ESC's
    4 x 2204 2300kv Brushless Cheerwing Motors

  2. #2
    Instructor Pilot RonSII's Avatar
    Join Date
    Dec 2011
    Location
    PNW USA
    Posts
    3,312
    So.... what kind of pdb do you have and how do you know it is burned out? got pics?

    First a higher C rating batt will allow more amps to be drawn through the pdb so if you burned it out a better batt will only burn it out quicker... if you mean part of the pdb that makes different voltages for cams,f/c's, etc is burned out then that is a different matter, either you have too much power required for the accessories you have on board for the pdb to handle or something is wired wrong... either way nee a bit more info here... like a wiring diagram, pics of the wiring/damage, things like that.

    Don't worry about not understanding a lot of the technical stuff to start with just do as much research as you can handle and it will start to click for you it's not rocket science but it can be overwhelming when you first jump in

  3. #3

  4. #4
    Navigator STI-REX's Avatar
    Join Date
    Aug 2012
    Location
    Alexandra Hills ,Brisbane , Australia
    Posts
    303
    Is the bottom of the PDB insulated from the carbon frame ?

    If the PDB has electrical connection with the carbon frame then that is most probably your short

    Remember carbon fiber is conductive
    4 wheels moving body 2 wheels moving soul

  5. #5
    Navigator jayhuc's Avatar
    Join Date
    Nov 2011
    Location
    Toronto,Canada
    Posts
    71
    could be the fact you have a 4000mah battery on mini quad. 4000!!! way too much. try a 1300 or even 1600. at most 2200. but the craft will run high on the throttle stick and cause heat. that's your problem. where in the throttle stick do you need to have it, in order to hover. My guess is no less then 3/4.

Similar Threads

  1. ESC burned?
    By Voya9er in forum TBS Support
    Replies: 2
    Last Post: 9th November 2015, 03:58 PM
  2. FS TX 3.2 L1 Burned
    By DOGNON in forum Fat Shark R/C Vision Systems
    Replies: 1
    Last Post: 24th April 2015, 02:40 AM
  3. Burned ESC's ?
    By mindoo in forum RC TECH
    Replies: 7
    Last Post: 18th April 2015, 05:44 PM
  4. ESC burned to a crisp
    By radialmind in forum TBS Support
    Replies: 0
    Last Post: 17th July 2014, 02:57 PM
  5. I think I burned out my tx.
    By breeze400 in forum ImmersionRC
    Replies: 10
    Last Post: 16th April 2013, 06:16 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •