TBS VENDETTA

[ryaske]

hi does anyone have a full teardown video/pictures of the vendetta 1, I need to fix the XT60 connector it comes out when i pull the LiPO off

I dont have the video but I can tell you, if your xt60 pulls out, you broke one of the two tabs that stick out of the XT60 (It's not a normal XT60). This happened ot me, I just hot glued it back in and it's been fine. The only way to fix it for sure is to buy aonther pigtail (with the XT60 with the tabs) and swap it in. I only found TBS selling them on their website.. have not been able to find the XT60 with tabs anywhere else.

Check out this thread, has pictures of the tabs, etc http://fpvlab.com/forums/showthread....-How-to-remove

[Psychomacgyver]

Carbon fiber is not conductive

[ryaske]

Carbon fiber is not conductive

Don't spread misinformation- take a watch of this or go buy a multimeter and test some for yoruself.

Cheap fiber glass (that is made to look like carbon fiber) is not conductive. But real Carbon fiber is certainly conductive.

[boxhead530]

Carbon fiber is not conductive

ah, could you explaine what your getting at?

when I used to destroy spacecraft, made with carbon fiber and many many different "glues" the bus had every joint finished with ground straps, and the "glue" for that was always the same, the "epathin" <spelling, its been along time ago> was a expoxy that had metal in it.
Yeah, there could be a layer of "glue" that may make a nonconductive surface, until it got scratched or "rubbed".
I do believe there's a "leasat" in orbit that broke because of a ground problem, I got sent to England, "menwithillstation", a army/navy base that we had to figure out how to get heated up, spun up, a month of work getting it hot" expand" to make a connection from despun bus ( antenna...stuff) to spun bus ( solar panels, battery's--nickel/hydrogen cells (( way expensive, way powerful, about the size of 1/2 gallon milk jug, could have worked on a big octo, maybe he he )) anyway put it on a track that let sunlight (in space) get to the space between despun and spinning shelfs and on a tube end ( aluminum) and gave the sat about half its power...oh...
oh yeah, I forgot where I was going with this...except that carbon fiber is conductive, and a pain to work with. Which is why I love my vendetta, the workmanship, the finish, I need the V2 so I can bash the v1 a little he he

so why did you say carbon fiber is conductive? Or was it a question?? a Alzheimer'sed mind want to know( well so sez UCDavis Alzheimer brain study...which is weird because remembering the leasat failure, and I just remb there also was a month of 24 hr spin test with Ln2 and 10.800 volts of quartz lamps for "sunshine" a 1100lbs spinning aluminum disk setup for flight, all the microwave stuff, batts, the damn bearing that let power move from despun to spundisk...

GO ALT LEFT! No to racism !

[boxhead530]

Don't spread misinformation- take a watch of this or go buy a multimeter and test some for yoruself.

Cheap fiber glass (that is made to look like carbon fiber) is not conductive. But real Carbon fiber is certainly conductive.

++++,++++++ 1

[mydiva]

Hey guys...I'll put a TBS Crossfire micro receiver in my Vendetta. Where did you put the Antenna and the second smaller antenna cable? Also did you put both in a shrinking tube for protection? THX!!

[Knotthrower]

Hi there,
Need some help with my Vendetta I. It flies fine in all modes and levels nicely in angle/horizon modes. Issue is when I do a flip side-side or front to back in horizon mode: it will not re-level and crashes. I tried rebooting the firmware already.
Many thx

[onit12]

Hey there,
i am new to FPV and race copters, so i would like to know if there is the possibility to use Return to Home, Position Hold or something like that with the TBS GPS and Betaflight Firmware?
Thanks
Tino

[mugenracerman]

Well I just purchased the vendetta v2 as and I am having an issue with one of my motors. I have to almost move the slider up to the max to get the motor running. I've tried swapping the arms to see if it was just a motor but it doesnt matter what motor it is. Im pretty new to using beta flight and race quads. I haven't touched the firmware yet on the quad and will try re flashing it. If any of ya'll know what might be the issue it will be much appreciated. I'm just hoping I didnt get a faulty ESC with this Vendetta. I am dying to fly.
Attachment 77061

Have you tried calibrating the ESCs or reflashed blheli on the ESCs?

Sent from my SM-G950U using Tapatalk

[CC268]

Has anyone used the Endurance Arms 7" on there Vendetta II? Thinking about ordering the arms. Almost impossible to find 7x4.5 props for it though.