Page 11 of 58 FirstFirst ... 91011121321 ... LastLast
Results 101 to 110 of 579

Thread: TBS Software Releases

  1. #101
    Navigator
    Join Date
    Oct 2013
    Posts
    544
    Quote Originally Posted by Perna View Post
    There is an extra setting to enable RC over mavlink. It's one page back from output mapping and it only showes up it channel 8 is set to mavlink. If both are set, yes you don't need any extra wire anymore. I think it would make sense to run the rc calibration again.
    Would there be any additional delay with mavlink rc compared to cppm?

  2. #102
    Pilot doobie's Avatar
    Join Date
    Jan 2015
    Location
    ontario canada
    Posts
    1,373
    Quote Originally Posted by Joesa3rd View Post
    I've experienced this as well. Something is up with that... Had to power back up again and on the next battery disconnect it was fine.
    I kinda think this has something to do with my xfire locking up. not sure though
    flyin HIGH

  3. #103
    Navigator
    Join Date
    Jan 2016
    Posts
    26
    Quote Originally Posted by Perna View Post
    I use APM 3.3.2. Maybe make sure your APM and mission planner is up to date.
    finally it is working, i had change it to serial 2 on pixhack and i got everything working from the first attempt. on serial 1 "radio" not a chance. thks for your time Perna !

  4. #104
    Quote Originally Posted by ammit View Post
    finally it is working, i had change it to serial 2 on pixhack and i got everything working from the first attempt. on serial 1 "radio" not a chance. thks for your time Perna !
    Do you mean sr1 values to sr2 ? Do you have picture of your setup.

  5. #105
    Navigator
    Join Date
    Aug 2014
    Posts
    295
    Quote Originally Posted by Perna View Post
    There is an extra setting to enable RC over mavlink. It's one page back from output mapping and it only showes up it channel 8 is set to mavlink. If both are set, yes you don't need any extra wire anymore. I think it would make sense to run the rc calibration again.
    Hi Perna: A question on mavlink for control.

    Does mavlink require a bi-directional connection for successful control? The reason I'm asking is that I understand the return transmission (from the RX) is quite significantly power-limited in comparison to the TX and would, assumedly, mean a far smaller range.

  6. #106
    Navigator
    Join Date
    May 2014
    Location
    Key Largo, FL
    Posts
    228
    Quote Originally Posted by Joesa3rd View Post
    I've experienced this as well. Something is up with that... Had to power back up again and on the next battery disconnect it was fine.
    If the TX isn't within a couple of feet from the RX when you power down, it triggers the beacon.

  7. #107
    Navigator
    Join Date
    Jan 2016
    Posts
    26
    Quote Originally Posted by Mesaman View Post
    Do you mean sr1 values to sr2 ? Do you have picture of your setup.

    Click image for larger version. 

Name:	Screenshot_2016-02-21-05-26-12.png 
Views:	127 
Size:	551.9 KB 
ID:	70620

    to "telemetry 2" port i have used the values from Perna's screenshot
    Last edited by ammit; 21st February 2016 at 05:58 AM.

  8. #108
    Quote Originally Posted by ammit View Post
    Click image for larger version. 

Name:	Screenshot_2016-02-21-05-26-12.png 
Views:	127 
Size:	551.9 KB 
ID:	70620

    to "telemetry 2" port i have used the values from Perna's screenshot

    ok, thanks! Will try that..

  9. #109
    Did you connect telemetry 2 through splitter board?

  10. #110
    Quote Originally Posted by Mesaman View Post
    Did you connect telemetry 2 through splitter board?
    I have minimosd connected to telem 2 / osd port so I don't think it is going to work with crossfire. Is there any chance it's going to work with telem 1 port?
    Last edited by Mesaman; 21st February 2016 at 07:47 AM.

Similar Threads

  1. FAA Releases B4UFLY Smartphone App
    By Papa Echo in forum sUAS LEGISLATION
    Replies: 11
    Last Post: 26th January 2016, 01:22 PM
  2. Lumenier releases "CS-600 Super" FPV Camera
    By timnilson in forum LUMENIER
    Replies: 52
    Last Post: 1st October 2014, 09:41 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •