Holy cow the cable that came with the PSU looks like I co uld jump start my car with it (Joke) - is it necessary for that guage of wire?
Currently have a USB cable already routed in the plane...will it be sufficient?
Holy cow the cable that came with the PSU looks like I co uld jump start my car with it (Joke) - is it necessary for that guage of wire?
Currently have a USB cable already routed in the plane...will it be sufficient?
KF7TRX
It may seem difficult at first, but everything is difficult at first - Myamoto Musashi
"Truly superior pilots are those who use their superior judgment to avoid those situations where they might have to use their superior skills"- Author unknown
we had to ship that one short term because of supply shortages, it's one gauge stronger than the one we ship normally. if it's too thick, send me a mail, we have the standard gauge wire back in stock, replacement is free of charge.
Last edited by Trappy; 25th January 2012 at 05:41 PM.
As long as we are on the wiring, I've seen bits and pieces of wiring these up.
Red from the TB-69 Camera should go to PSU?
All else to EzOSD INPUT
EzOSD Output to VTX except red- red goes to PSU Power.....?
I'm just tired and there's a million different schematics...
KF7TRX
It may seem difficult at first, but everything is difficult at first - Myamoto Musashi
"Truly superior pilots are those who use their superior judgment to avoid those situations where they might have to use their superior skills"- Author unknown
no, you basically wire the PSU between OSD and camera, or between OSD and video TX. Here's the rough idea:
Camera --------------- PSU ---- OSD -------------------------- VTx
or
Camera ------------------------- OSD ---- PSU ---------------- VTx
That is assuming you have a 5V Vtx, of course. The PSU is made so that current to one side is 12V, the current to the other side is 5V, regardless of what comes in through the power pins. The EzOSD will just pass through the power.
Thats how I wired everything in my zephyr. maybe it helps:
FPV killed my bank account
So the Lawmate 2.4ghz Vtx is powered from the EzOSD then?
That's where the confusion lies - I'd just soon wire the camera to the OSD, and run a cable to the Vtx ...
I'm assuming it's a 5v Vtx, Lawmate, came from Canada....via the UK LOL
KF7TRX
It may seem difficult at first, but everything is difficult at first - Myamoto Musashi
"Truly superior pilots are those who use their superior judgment to avoid those situations where they might have to use their superior skills"- Author unknown
The main power for the psu comes from the batteries throught the current sensor. The psu steps that down to 5V. And that goes into the lawmate TX.
Check out the diagramm above. It works.
Last edited by egosession; 25th January 2012 at 08:37 PM.
FPV killed my bank account
LOL Yours was the schematic I've been using so far...very good job on itOriginally Posted by egosession
Ooooh you have a rescue battery - do you hae the diode set up in it? - That'll be a next month thing after I've flown a few times..
KF7TRX
It may seem difficult at first, but everything is difficult at first - Myamoto Musashi
"Truly superior pilots are those who use their superior judgment to avoid those situations where they might have to use their superior skills"- Author unknown
OK and video runs through it as well then based on teh schematics and pics on team-blacksheep's site...think that's where my confusion also lay..
KF7TRX
It may seem difficult at first, but everything is difficult at first - Myamoto Musashi
"Truly superior pilots are those who use their superior judgment to avoid those situations where they might have to use their superior skills"- Author unknown
correct. that greatly simplifies the wiring! the TBS PSU already has a diode on it. We're not amateurs, you know ...
Posting Permissions
Reply With Quote
