image
Tab Content
More Activity

41 Visitor Messages

  1. View Conversation
    Hi ssassen thanks for replying to the thread about the camera setting via the osd for the vortex you did comment that the cable with the joystick can be used for the settings on the UMMAGAWD can this cable be used for the 250 pro also I just wanted to see if the wdr was actually turned on also to try get the picture a little brighter any help would be very much appreciated as in just months into this hobby and am keen to learn fast thanks
  2. View Conversation
    Hey Sander,
    sorry for the direct message, but mybe you have a spare minute to look at this thread?
    http://fpvlab.com/forums/showthread....ceiver-Modules
    I am pretty sure you can answer that in seconds

    Thank you in advance,
    Achim
  3. View Conversation
    lớp học kế toán tại cầu giấy thực hành thực tế của công ty kế toán hà nội,Nếu bạn ở long biên có thể tha gia lớp học kế toán tại long biên,
    ngoài ra c̣n có lớp học kế toán tại hà đông và lớp học kế toán tại bắc ninh
  4. View Conversation
    Hey there,
    I'd like to draw your attention to my ezuhf range problem (350 meters before failsave) posted here:
    http://fpvlab.com/forums/showthread....l=1#post669306
    Thanks a lot,
    William
  5. View Conversation
    Hello Sander,

    I refer to this thread: http://fpvlab.com/forums/showthread....hf+lose+signal

    I have a very simillar issue,

    Problem:

    EZUHF TX loses signal at about 1.2km range and my quad goes into failsafe, at that range i still have video feed to my goggles running 5.8ghz, could you advise me on what i should do to resolve the problem?

    My setup:

    TBS Discovery with TBS Core (No tin shield)
    EZUHF 8CH Lite RX
    VTX: IRC 250mw 5.8ghz with IRC spironet
    Naza M lite w/GPS
    Frsky Tanaris with EZUHF JR style module w/ Diamond antenna

    If you require any other info or pictures please let me know, i look forward to your reply!

    Regards,

    Jonathan
  6. View Conversation
    Today i tried to install EZ LRS at my system.
    Everything was ok, except for the RSSi values at the ImmersionRCTools.
    The values appear between -25 to -35 with the TX within 1m of the RX.
    The problem occurs with 2 RXs.
    My check list done:
    TX and RX are with the same firmware version 1.50 and same frequency band:430-450mhz extreme hopping;
    I power the TX with a dedicated 3S Lipo;
    I install another firmware versions, but the problem continues.
    I change the TX antenna, but nothing.
    I did the ground test. With 20mW TX after 18 steps from the RX the signal is lost and enter in FS mode. And the immersion tools shows -86dBm.
    I install the TX at another radio and the problem continues.
    I bind my 2 RX with another TX and the immersion tools shows 0dBm in both. At the range test, with 20mW i walk 30 steps from the RX and got -30dBm, good signal.

    http://fpvlab.com/forums/showthread....152#post643152

    can you help me?

    Tks
    Mzz
  7. View Conversation
    Hello there, I am trying to locate a copy of the firmware 1.25a(6), as my USB connector on my tx is damaged and i just recently bought another rx, in which i cannot bind it due to the fact my tx is at 1.25a. Any help with this is appreciated.. Thanks VT
  8. View Conversation
    Hello there, I am trying to locate a copy of the firmware 1.25a(6), as my USB connector on my tx is damaged and i just recently bought another rx, in which i cannot bind it due to the fact my tx is at 1.25a. Any help with this is appreciated.. Thanks VT
  9. View Conversation
    Hello Sander Sassen,

    I have a problem and I don't know who would help me.
    I got you a recommendation as to the last instance of that could help me.
    My whole problem is described here - http://fpvlab.com/forums/showthread....oscam5.8/page2
    Can you help me?

    Thank you for your quick answer.


    Regards
    VSCharlie
  10. View Conversation
    My 600Mw 5.8 Tx just stopped working. Less tan a year old. No crashes. Been great until now. How can I get this repaired? The LED is barely coming on and its illumination is erratic going from bright to dim. But no video transmission. Have checked all cables with other immersion Tx's I have and all is good.

    Please advise.
Showing Visitor Messages 1 to 10 of 41
Page 1 of 5 123 ... LastLast
Page 1 of 5 123 ... LastLast
About ssassen

Basic Information

Date of Birth
June 27, 1974 (43)
About ssassen
Biography:
Dual battery setup and GoPro for piloting evangelist
Location:
Netherlands
Interests:
Scrabble, interstellar gas cloud physics, bean counting, hot lesbian p0rn
Occupation:
Waterbottle replacement guy at ImmersionRC

Signature


Purveyor of the FPV secret sauce at ImmersionRC

Statistics


Total Posts
Total Posts
9,603
Posts Per Day
4.06
Last Post
Thread ender. 15th August 2017 05:27 AM
Visitor Messages
Total Messages
41
Most Recent Message
7th August 2017 12:36 PM
General Information
Last Activity
17th August 2017 03:26 AM
Join Date
25th February 2011
Referrals
14

5 Co-Pilots

  1. boopidoo boopidoo is offline

    Pilot

    boopidoo
  2. CaliDave CaliDave is offline

    Instructor Pilot

    CaliDave
  3. FatShark FatShark is offline

    Wireless video evangelist

    FatShark
  4. Gerard Gerard is offline

    Navigator

    Gerard
  5. timnilson timnilson is offline

    Lumenier.com

    timnilson
Showing Friends 1 to 5 of 5